Vertex Standard FT-857 manual Mic Sel

MENU OPERATION

No	Menu Item	Function	Available Values	Default
059	MIC SEL	The choice of the equipment which connects to the	NOR/RMT/CAT	NOR
		MIC jack.
060	MTR ARX SEL	Select the analog meter display configuration while	SIG, CTR, VLT, N/A, FS,	SIG
		the transceiver is receiving.	OFF
061	MTR ATX SEL	Selects the analog meter display configuration	PWR, ALC, MOD, SWR,	PWR
		while the transceiver is transmitting.	VLT, N/A, OFF
062	MTR PEAK HOLD	Enabling/disabling of the “peak hold” function of the	ON/OFF	ON
		meter.
063	NB LEVEL	Setting of the blanking level for the IF Noise	0 ~ 100	50
		Blanker.
064	OP FILTER 1	Not available at this time.	–	–
065	PG A	Programming the [A] key (in the Operating		MONI
		Function Row “q” (MFq)) function.
066	PG B	Programming the [B] key (in the Operating		Q. SPL
		Function Row “q” (MFq)) function.	All Multi Function,
067	PG C	Programming the [C] key (in the Operating		ATC
		Function Row “q” (MFq)) function.	All Menu Item, MONI,
068	PG ACC	Programming the optional MH-59A8J microphone’s	Q.SPL, TCALL, ATC and	MONI
		[ACC] button assignment.	USER.
069	PG P1	Programming the optional MH-59A8J microphone’s		Q. SPL
		[P1] button assignment.
070	PG P2	Programming the optional MH-59A8J microphone’s		TCALL
		[P2] button assignment.	0 ~ 100
071	PKT 1200	Adjusts the audio input level from the TNC during		50
		1200 bps Packet operation.
072	PKT 9600	Adjusts the audio input level from the TNC during	0 ~ 100	50
		9600 bps Packet operation.
073	PKT RATE	Sets the transceiver’s circuitry for the Packet baud	1200/9600 (bps)	1200 bps
		rate to be used.
074	PROC LEVEL	Sets the compression level for the AF speech	0 ~ 100	50
		processor in the SSB/AM modes.
075	RF POWER SET	Setting of the maximum power level for the current	5 ~ 100	ø2
		band.	2 ~ 100 (UHF)
076	RPT SHIFT	Sets the magnitude of the repeater shift.	0.00 ~ 99.99 (MHz)	ø2
077	SCAN MODE	Selects the desired Scan-Resume mode.	TIME/BUSY/STOP	TIME
078	SCAN RESUME	Sets the delay time for scanning resumption.	1 ~ 10 (sec)	5 sec
079	SPLIT TONE	Enables/disables split CTCSS/DCS cording.	ON/OFF	OFF
080	SQL/RF GAIN	Selects the configuration of the front panel’s SQL/	RF-GAIN/SQL	ø1
		RF knob.
081	SSB MIC GAIN	Adjusts the microphone gain level for the SSB	0 ~ 100	50
		mode.
082	SSB STEP	Selects the tuning steps for the MEM/VFO CH	1kHz/2.5kHz/5kHz	2.5kHz
		knob on the SSB mode.
083	TONE FREQ	Setting of the CTCSS Tone Frequency.	50 Standard CTCSS tones	88.5 Hz
084	TOT TIME	Select the Time-Out Timer time.	OFF/1 ~ 20 (min)	OFF
085	TUNER/ATAS	Selects the device (FC-30 or ATAS-100/-120) to be	OFF/ATAS(HF)/	OFF
		controlled via the front panel’s [A](TUNE) key.	ATAS(HF&50)/ATAS(ALL)/
			TUNER
086	TX IF FILTER	Selects the Transmit IF filter.	CFIL/FIL1/FIL2	CFIL
087	VOX DELAY	Sets the “hang time” for the VOX circuitry.	100 ~ 3000 (ms)	500 ms
088	VOX GAIN	Sets the gain of the VOX circuitry’s input audio	1 ~ 100	50
		detector.
089	XVTR A FREQ	Allows an arbitrary frequency to be set on the		–
		display, to allow direct frequency readout during	0,000,00 ~ 9999,999,00
090	XVTR B FREQ	transverter operation.	(kHz)	–
		Enables/disables/selects the antenna port to be	OFF/X VTR A/X VTR B
				OFF
091	XVTR SEL
		used for Transverter operation.

ø1: Depends on transceiver version.

ø2: Depends on operating band and transceiver version.

96 FT-857 Operating Manual