DLP Projjecttor—User’s Manuall
LED Error Messages
| ERROR CODE MESSAGES |
|
| POWER LED |
|
| READY LED |
|
| OVERHEAT LED |
|
|
|
| BLINK |
|
| BLINK |
|
|
| ||
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| Over temperature |
| 0 |
| 0 |
|
| ON |
| ||
|
|
|
|
|
|
|
|
| |||
| Thermal Break |
| 4 |
| 0 |
| 0 |
| |||
|
|
|
|
|
|
|
|
| |||
| G794 fail |
| 4 |
| 4 |
| 0 |
| |||
|
|
|
|
|
|
|
|
| |||
| T1 fail |
| 4 |
| 5 |
| 0 |
| |||
|
|
|
|
|
|
|
|
| |||
| PING code error |
| 4 |
| 6 |
| 0 |
| |||
| Lamp error |
| 5 |
| 0 |
| 0 |
| |||
|
|
|
|
|
|
|
|
| |||
| Ballast Over Temperature |
| 5 |
| 1 |
| 0 |
| |||
|
|
|
|
|
|
|
|
| |||
| Ballast shot circuit in output detected |
| 5 |
| 2 |
| 0 |
| |||
|
|
|
|
|
|
|
|
| |||
| End of lamp lift detected |
| 5 |
| 3 |
| 0 |
| |||
|
|
|
|
|
|
|
|
| |||
| Ballast lamp did not ignite |
| 5 |
| 4 |
| 0 |
| |||
| Lamp extinguished during normal |
| 5 |
| 5 |
| 0 |
| |||
| operation |
|
|
|
|
|
|
|
|
|
|
| Lamp extinguished during |
| 5 |
| 6 |
| 0 |
| |||
| phase |
|
|
|
|
|
|
|
|
|
|
| Fan1 error (Lamp Fan) |
| 6 |
| 1 |
| 0 |
| |||
|
|
|
|
|
|
|
|
| |||
| Fan2 error (Ballast Fan) |
| 6 |
| 2 |
| 0 |
| |||
|
|
|
|
|
|
|
|
| |||
| Fan3 error (Burner Fan) |
| 6 |
| 3 |
| 0 |
| |||
|
|
|
|
|
|
|
|
| |||
| Fan4 error (Power Fan) |
| 6 |
| 4 |
| 0 |
| |||
|
|
|
|
|
|
|
|
| |||
| Lamp door open |
| 7 |
| 0 |
| 0 |
| |||
|
|
|
|
|
|
|
|
| |||
| DMD error |
| 8 |
| 0 |
| 0 |
| |||
|
|
|
|
|
|
|
|
| |||
| Color wheel error |
| 9 |
| 0 |
| 0 |
| |||
|
|
|
|
|
|
|
|
|
|
|
|
In the event of an error, please disconnect the AC power cord and wait for one (1) minute before re- starting the projector. If the POWER or READY LEDs are still blinking or the OVERHEAT LED is lit, contact your service center.
Image Problems
Problem: No image appears on the screen
1.Verify the settings on your notebook or desktop PC.
2.Turn off all equipment and power up again in the correct order.
Problem: The image is blurred
1.Adjust the Focus on the projector.
2.Press the Auto button on the remote control or projector.
3.Ensure the
4.Check that the projector lens is clean.
Problem: The image is wider at the top or bottom (trapezoid effect)
1.Position the projector so it is as perpendicular to the screen as possible.
2.Use the Keystone button on the remote control or projector to correct the problem.
– 42 –
