Manuals / Vulcan-Hart / Kitchen Appliance / Fryer

Vulcan-Hart 1GR45CF ML-136791 manual Boil Out Procedure, Thermal Overload Protection Button

Models: 1GR65CF ML-136792 1GR65C ML-136415 1GR65D ML-136412 1GR45C ML-136414 1GR45CF ML-136791 1GR85C ML-136416 1GR45D ML-136411 1GR45DF ML-136778 1GR65DF ML-136789 1GR85DF ML-136790 1GR85CF ML-136793 1GR85D ML-136413 2GR45CF ML-136431 2GR45DF ML-136424 3GR45DF ML-136427

1 27

Download 27 pages 3.39 Kb

Page 25

BOIL OUT PROCEDURE:

GRDF / GRCF SERIES GAS FRYERS

BOIL OUT PROCEDURE:

Use the Boil Out By-Pass™ drain extension allowing the boil out solution to exit the fry tank without using the filtering system. Do not allow water to run through the motor / pump. Drain the boil out solution into a bucket or place a hose on the end of the drain extension allowing the other end to flow into a floor drain. In Fig. 6 the arrow is pointing to the drain extension. It is threaded into the top coupling of the oil drain tube. Drain extension needs to be only hand tightened.

THERMAL OVERLOAD PROTECTION BUTTON:

The motor/pump supplied with the filtering system has a thermal overload protection circuit that senses when excess heat occurs due to filtering for long periods of time or under heavy load prior to discarding debris buildup. If the thermal overload protection is tripped, wait 5 minutes and then reset the motor by pushing in the red button. The arrow in Figure 7 shows the location of the reset button; located on the front off the motor / pump facing towards you.

VULCAN-HART

Fig. 6

Fig. 7

F-32933 Rev. G (May 2009)

-25-

Image 25

Vulcan-Hart 1GR45CF ML-136791, 3GR45DF ML-136427, 2GR45DF ML-136424 Boil Out Procedure, Thermal Overload Protection Button

Contents

GRD & GRC SERIES GAS FRYERS With KleenScreen PLUS Filtration Systems INSTALLATION & OPERATIONAL MANUALMODELS FOR YOUR SAFETY IMPORTANT FOR YOUR SAFETYTABLE OF CONTENTS ORDERING PARTS INTRODUCTIONUNPACKING GENERALFryer Model No Device Serial No Clearances INSTALLATIONLocation CODES AND STANDARDS ASSEMBLYIn the United States In CanadaFLUE CONNECTION Use soap and water solution. Do not use an open flameELECTRICAL CONNECTION GAS CONNECTIONGAS PRESSURES ALL MODELS TESTING THE GAS SUPPLY PIPING SYSTEMFryers with Casters LEVELING THE FRYER OVER-TEMPERATURE SHUTDOWNOPERATION BEFORE FIRST USE CleaningFILLING TANK WITH SHORTENING EXTENDING SHORTENING LIFE BASIC FRYING INSTRUCTIONFry Basket Guidelines Fry Basket CapacityEXTENDED SHUTDOWN TURNING ON THE FRYERFILTERING THE OIL GRDF / GRCF SERIES GAS FRYERS Programming the Solid State ControlVULCAN-HART F-32933 Rev. G MayGRDF / GRCF SERIES GAS FRYERS Programming the Computer ControlVULCAN-HART F-32933 Rev. G MayWeekly or when oil is replaced BOIL OUT PROCEDUREDRAINING THE TANK Daily CLEANINGKleenScreen Plus Filtration System Installation and Operational Manual for “DF” and “CF” ModelsGRD/CF and 2XGD/CF Models GAS KleenScreen PLUS ModelsFiltering Instructions for KleenScreen PLUS Fryers AssemblySuction Tube Filter Screen Filter Insert Knurled Bottom Fitting GeneralMicro-Filtration Fabric Envelope Assembly Fully assembled filter screen assemblyFabric Envelope Insert Different from Screen Assembly Fabric Envelope Secure Tube with Suction Tube Clip Filter Screen LaysDO NOT WASH FABRIC ENVELOPE INSTRUCTIONS TO REMOVE & REPLACE KLEENSCREEN PLUS FILTER ENVELOPEStep StepOperation FILTERING PROCEDUREVULCAN-HART GRDF / GRCF SERIES GAS FRYERSF-32933 Rev. G May VULCAN-HART GRDF / GRCF SERIES GAS FRYERSF-32933 Rev. G May REMOVING EXCESS DEBRIS FROM THE SCREEN FILTER FILTERING TIPFLUSH AND DISCARD THERMAL OVERLOAD PROTECTION BUTTON BOIL OUT PROCEDUREALARMS AND ERROR MESSAGES MAINTENANCEService in the US and Canada FLUE VENT INSPECTIONTroubleshooting Chart