Manuals / Vulcan-Hart / Kitchen Appliance / Fryer

Vulcan-Hart GRD35 ML-052080 Leveling Fryer, Flue Connections, Electrical Connections

Models: GRC65 ML-052085 GRD25 ML-052513, GRD35 ML-052080, GRD45 ML-052081, GRD65 ML-052082, GRD85 ML-052306, GRC35 ML-052083, GRC45 ML-052084, GRC65 ML-052085, GRC85 ML-052307, GRD35F ML-126732, GRD45F ML-126735, GRD65F ML-126738, GRD85F ML-126741, GRC35F ML-126433, GRC45F ML-12 GRC45 ML-052084 GRC35 ML-052083 GRD25 ML-052513 GRD65 ML-052082 GRD45 ML-052081 GRC45F ML-12 GRD35 ML-052080 GRC85 ML-052307 GRD85 ML-052306

1 36

Download 36 pages 20.69 Kb

Page 13

LEVELING FRYER

1.Place a spirit level on top of the fryer after gas connections have been made.

2.Adjust the legs to ensure that the fryer is level front-to-back and side-to side in the final installed position.

FLUE CONNECTIONS

The fryer must be located under a hood with adequate connection to an exhaust duct. The hood must extend 6" (15 cm) beyond fryer sides.

Adequate ventilation must be provided and comply with Vapor Removal from Cooking Equipment, ANSI-NFPA Standard #96 (latest edition), available from the National Fire Protection Association, Batterymarch Park, Quincy, MA 02269.

Clearance above the fryer should be adequate for combustion byproducts to be removed efficiently. An 18" (46 cm) minimum clearance should be maintained between the flue vent and the filters of the hood venting system. Never make flue connections directly to the fryer.

Do not obstruct the flow of the flue gases from the appliance. Proper air balance should be maintained in the room.

ELECTRICAL CONNECTIONS

WARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE NATIONAL ELECTRICAL CODE AND/OR OTHER LOCAL CODES.

WARNING: APPLIANCES EQUIPPED WITH ELECTRICAL SUPPLY CORD(S) ARE PROVIDED WITH A THREE-PRONG GROUNDING PLUG, WHICH MUST BE CONNECTED TO A PROPERLY GROUNDED RECEPTACLE. IF THE RECEPTACLE IS NOT THE PROPER GROUNDING TYPE, CONTACT AN ELECTRICIAN. DO NOT REMOVE THE GROUNDING PRONG FROM THE PLUG.

Fryers are equipped with a 120 V, 60 Hz, 1-phase cord and plug.

Do not connect fryer to electrical supply until after gas connections have been made.

– 13 –

Image 13

Vulcan-Hart GRD35 ML-052080, GRD85 ML-052306, GRC85 ML-052307 Leveling Fryer, Flue Connections, Electrical Connections

Contents

Installation GRD and GRC Series GAS Fryers For Your Safety Important for Your SafetyTable of Contents Table of Contents General SpecificationsBattery Configurations Options and FeaturesNon Filter Models C DFilter Fryer Fryer Fryer Dump Filter Fryer Dump Fryer Fryer Fryer Fryer Dump FryerRO Series Frymate Features FIELD-INSTALLED Accessories FACTORY-INSTALLED OptionsGR Series Frymate Dump Station Heat Lamp TopsUnpacking InstallationLocation Installation Codes and StandardsUnited States of America CanadaFryers Mounted on Legs Non-Batteried Fryers AssemblyFryers Mounted on Casters GAS Connections Testing the GAS Supply Piping SystemGAS Pressures and Orifices Flue Connections Leveling FryerElectrical Connections Before First USE OperationSeasoning Filling FRY Tank with ShorteningLighting Instructions for Manual Pilot Ignition Fig Startup with Electronic Igniter Controls GRD SeriesControl Guide Programming Guide ProgrammingMelt Options GRD Series Shutdown Models With Basket Lift OptionExtended Shutdown Controls GRC SeriesParameter Steps Left Display Right Display Set Back Heating Melt L Melt S Melt Options GRC SeriesDispose Temperature Temperature and Time ProgrammingTime Advanced Time Features Setting Advanced Time Features Time Programming Quick Chart Shutdown Fry Basket Guidelines Frying Guidelines All ModelsRecommended Basket Capacities Filtering Guidelines All Models Daily FilteringFilter-Ready Fryers For Use With Mobile Filter Only Filtering Procedures Non-Filter-Ready Fryers Battery Interplumbing Only Available on KleenScreen ModelsHigh Limit Device All Models Drain Interlock GRD and GRC SeriesDaily CleaningWeekly or AS Required Service MaintenanceLubrication VentSymptom Possible Causes Troubleshooting GuidePilot OUT Alarms and Error Messages GRD and GRC Series