side.
Important: The dimension between the flag angles must be:
For 2” track applications: door width plus
For 3” track applications: door width plus
Complete the vertical track installation by securing the jamb bracket(s) or slots in the wall angle and tightening the other lag screws. Push the vertical track against the track rollers so that the track rollers are touching the deepest part of the curved side of the track; tighten all the track bolts and nuts. Repeat for other side.
| Door width (2” Track) | Door width (3” Track) | |
Top of flag angle or | + | + | |
|
| ||
Top of wallangle assembly |
|
| |
2” Track Applications: | Nail |
| |
Top section | |||
3” Track Applications: |
|
| |
|
|
| Flag angle or |
| wallangle assembly |
| Top |
| section |
| Vertical track |
| against rollers |
15 | Horizontal Tracks |
Tools: Ratchet wrench, 7/16” Socket, 9/16” Socket, 9/16” Wrench, |
To install horizontal track, place the curved end over the top track roller of the top section. Align the bottom rail of the horizontal track with the top of the vertical track. Tighten the bot- tom rail of the horizontal track to the flag angle or wall angle with (2)
16 | Adjusting Top Fixtures |
Tools: 7/16” Wrench, Step ladder |
With horizontal tracks installed, you can now adjust the top fixtures.
NOTE: If your door came with two top fixtures, then one top fixture is required to be adjusted for each side.
NOTE: If your door came with four top fixtures, then two top fixtures are required to be adjusted for each side.
Starting on the left hand side, vertically align the top section of the door with the lower sec- tions. Maintaining the top fixture(s) position, tighten the
| Flag angle | Left hand top fixture(s) | |
| Top | (2) 1/4” - 20 Flange hex nuts or | |
| rail | ||
| (2) 1/4” - 20 x | ||
|
| ||
Horizontal |
| (2) 1/4” - 14 x 1” | |
| Lag screws | ||
tracks | Track roller | ||
| |||
|
| ||
|
| Top section |
17 | End Bearing Brackets |
Tools: Step ladder, Power drill, 7/16” Socket driver |
NOTE: Right and left hand is always determined from inside the garage looking out. End bearing brackets are right and left hand.
Identify the end bearing brackets supplied with your door.
Align the bottom edge of left end bearing bracket with the top edge of the flag angle. Main- taining this alignment, also align the right edge of the end bearing bracket with the right edge of the flag angle.
Secure the end bearing bracket to the jamb using (3) 5/16” x
|
| Flag angle |
|
|
| |
Bottom rail of |
|
|
| |||
Bottom rail of | ||||||
horizontal track |
| |||||
| horizontal track | |||||
|
|
|
(2) | (2) | ||
Flange hex nuts | |||
Flange hex nuts | |||
|
| ||
Vertical | (2) | Vertical | |
track | track | ||
| Track bolts |
|
Wall angle
(2) |
Track bolts |
| Left end bearing | Left end bearing |
| bracket | bracket |
|
| (3) 5/16” x |
|
| Lag screws |
| Bottom |
|
Top edge | edge |
|
of flag |
|
|
angle |
|
|
WARNING
Do not raise door until horizontal tracks are secured at rear, as outlined in step, Rear Back Hangs, or door could fall from overhead position causing severe or fatal injury.
Level the horizontal track assembly.
For riveted track assembly, bolt the top rail of the horizontal track to the first encountered slot in the flag angle using (1)
For wall angle track assembly, first bolt the angle of the horizontal track to the slots in the wall angle using (2)
Repeat for other side.
Remove the nail that was temporarily holding the top section in place, installed in step, Top Section.
Important: Failure to remove nail before attempting to raise door could cause permanent damage to top section.
Top | Top |
section | section |
Position the left hand end bearing bracket up against the jamb and the horizontal track, as shown. Fasten the left hand end bearing bracket to the horizontal track with (1)
Left end bearing | (3) 5/16” x | Left end bearing bracket |
bracket | Lag screws | (1) |
|
| |
|
| Truss head bolt |
| (1) |
|
| Hex nut | Upper |
|
| |
|
| slot |
(1) | (2) | |
Washer |
| (1) |
|
| Flange hex nut |
|
| Washer |
|
| Top rail of |
|
| horizontal track |
Top rail of |
|
|
horizontal track | (1) | |
| ||
|
| Track bolt |
|
| Flag angle |
(2)
(1)
Wall angle
Horizontal | Horizontal |
track | track |
11
Please Do Not Return This Product To The Store. Contact your local
refer to your local yellow pages business listings or go to the Find a Dealer section online at