Wayne-Dalton 5155, 5150, 5200, 5255 Sideroom Requirements, inch TRACK, Fig. AA, Fig. BB, Fig. CC

STEP 13: Operator Trolley Bracket Installation: Attach the operator trolley bracket as illustrated in Fig. AA. This trolley bracket is limited to doors 14’2” X 10’ (5 Sections high and smaller).

For doors 14’2” X over 10’ (5 sections) and 14’3” thru 20’2” by all heights see Fig. BB. For doors over 20’2” by all heights see Fig. CC.

EXTEND JAMBS TO OPENING HEIGHT plus

DIM Y plus 1 1/2” (MINIMUM LENGTH)

U-BAR

OPERATOR BRACKET

(3)1/4-20 X 7/8” SELF DRILLING TEK SCREWS

MODELS 5150, 5155, 5200, &5255 PART NUMBER 107319

DOORS UP TO 14 ft 2 in WIDE X 10’ (5 SECTIONS HIGH)

NOTE: TROLLEY BRACKET TO BE INSTALLED OFFSET FOR ODD PANELS

(4)1/4-20 X 5/8” SELF DRILLING TEK SCREWS

MINIMUM
HEADROOM	DIM Y
REQUIRED
	HEADER TO
(REFER TO
	SHAFT
HEADROOM
	CENTERLINE
CHART)

8” for 2” TRACK 12” for 3” TRACK

TORSION SHAFTS REQUIRE 10” OF SIDEROOM FOR SOLID SHAFTS and

5” OF SIDEROOM FOR TUBULAR

SHAFTS

Fig. AA

U-BAR	(6) 1/4-20 X 7/8” SELF
	DRILLING TEK SCREWS

OPERATOR BRACKET

NOTE: HEADROOM CAN BE REDUCED 2-1/2” BY USING THE QUICK CLOSING TOP FIXTURE OR BY SHORTENING THE VERTICAL TRACKS BY 3” MAX.

SIDEROOM REQUIREMENTS

2 inch TRACK

5/16 X 1”

DRILLING /

(4) 1/4-20 X 7/8” SELF DRILLING TEK SCREWS THROUGH OPERATOR BRACKET INTO GIRT

Fig. BB

6” GIRT

(12) 1/4-20 X 7/8” SELF DRILLING TEK SCREWS

(4)1/4-20 X 5/8” SELF DRILLING TEK SCREWS

MODELS 5150, 5155, 5200, & 5255 PART NUMBER 295689

THIS DESIGN IS FOR DOORS UP TO 14’ 2” WIDE AND OVER

10’ (5 SECTIONS HIGH) AND

14’3” THRU 20’2” BY ALL HEIGHTS NOTE: TROLLEY BRACKET TO BE INSTALLED OFFSET FOR ODD PANELS

TAPPING

SCREW

3/8 X 3” MIN.	3/8 X 3” MIN.
	SLEEVE
SLEEVE
	ANCHOR
ANCHOR
1” OVERLAP	1” OVERLAP	1” OVERLAP
1/2”- 5/8”	1/2”- 5/8”		1/2”- 5/8”
2 1/2” MIN.	2 1/2” MIN.	2 1/2” MIN.
SIDE ROOM	SIDE ROOM	SIDE ROOM
4 3/4”	4 3/4”
			1 1/2”
	1 1/2”	5/16 X 1”	3 1/2”
1 1/2”
		DRILLING /
3 1/2”	3 1/2”	TAPPING
		SCREW
OPTIONAL	OPTIONAL
MOUNTING	MOUNTING
BRACKET	BRACKET
PRECAST WALL WITH	PRECAST WALL WITHOUT		STEEL JAMBS
CORNER ANGLE	CORNER ANGLE		2” TRACK
2” TRACK	2” TRACK
	3 inch TRACK
5/16 X 1”
DRILLING /

FLUSH

1/2”- 5/8”

3 1/2” MIN.

SIDE ROOM

5/16 X 1 5/8”

1 1/2” LAG SCREW

3 1/2”

2” X 6” JAMB IS RECOMENDED

WOOD JAMBS

2” TRACK

OPERATOR

BRACKET

Fig. CC

MODELS 5155 & 5255

PART NUMBER 293009 38in WIDE X 19 5/8 in HIGH FOR 24 in TOP SECTION PART NUMBER 293010 38in WIDE X 16 7/16 in HIGH FOR 21 in TOP SECTION ATTACH USING (12) PRE DRILLED HOLES

MODELS 5150 & 5200

PART NUMBER 295687 50 in WIDE X 17 1/4 in HIGH FOR 24 in TOP SECTION PART NUMBER 295686 50 in WIDE X 14 in HIGH FOR 21 in TOP SECTION MOUNT BRACKET OVER HINGES IN CENTER OF SECTION, DRILL (2) 9/32” HOLES IN EACH CORNER AND SECURE USING (12) 14-20” X 7/8” SELF DRILLING TEK SCREWS (SEE NOTE BELOW)

THIS RECTANGULAR DESIGN IS FOR DOORS OVER 20 ft. 2 in. WIDE. NOTE: MODEL 5150 & 5200 DOORS BETWEEN 20 ft 2 in AND 24 ft 2 in

REQUIRE THAT THE OPERATOR BE MOUNTED OFF CENTER SO THE OPERATOR BRACKET MOUNTS TO THE HINGE POINTS.

PG. 14

TAPPING
SCREW
3/8 X 3” MIN.	3/8 X 3” MIN.
	SLEEVE
SLEEVE	ANCHOR
ANCHOR
1” OVERLAP	1” OVERLAP	1” OVERLAP
1/2”- 5/8”	1/2”- 5/8”		1/2”- 5/8”
3” MIN.	3” MIN.	3” MIN.
SIDE ROOM	SIDE ROOM	SIDE ROOM
4 3/4”	5”
		1”
		4”
1”	1”	5/16 X 1”
4”	4”	DRILLING /
		TAPPING
		SCREW
OPTIONAL	OPTIONAL
MOUNTING	MOUNTING
BRACKET	BRACKET
PRECAST WALL WITH	PRECAST WALL WITHOUT	STEEL JAMBS
CORNER ANGLE	CORNER ANGLE	3” TRACK
3” TRACK	3” TRACK	PG. 3

FLUSH

	1/2”- 5/8”
5” MIN.
SIDE ROOM
1”	5/16 X 1 5/8”
4”	LAG SCREW

2” X 6” JAMB IS RECOMENDED

WOOD JAMBS

3” TRACK