Weber Liquid Propane Grill, 55052 0100 specification





1.	Hinge Pin	27.	Hair Pin Cotter

2.	Left Endcap	28.	Thermometer

3.	Shroud	29.	Right Endcap

4.	Handle	30.	Burner Control Knobs

5.	Warm-Up™Basket	31.	Control Panel


6.	Warming Rack	32.	Ignitor Button


7.	Cooking Grates	33.	Control Panel Hardware


8.	Flavorizer® Bars	34.	Side Burner


9.	Cooking Box	35.	Crossover tube


10.	1/4-20 keps nut	36.	Front and Back Burners


11.	Slide Out Bottom Tray	37.	Center Burner


12.	Catch pan holder	38.	Spider Stopper Guards
13.	Catch pan	39.	Manifold, Hose and regulator (assembled)
14.	Left end trim piece	40.	Manifold Support Bracket
15.	Work Surface	41.	Manifold Hardware
16.	Front Panel	42.	Disposable Drip Pan
17.	Swing-Up Work Surface Rod	43.	Back Panel
18.	Left Swing-Up Work Surface	44.	Left Frame
19.	Caster Frame	45.	1/4-20 x 1/2 inch bolts
20.	1/4-20 x 2 inch bolts	46.	Right Frame
21.	Nylon Washers	47.	Igniter
22.	Bottom Shelf	48.	Right End Trim Piece
23.	Frame Connectors	49.	Wheel Frame
24.	Casters	50.	Right Swing-Up Work Surface
25.	Wheels	51.	Axle
26.	Hubcap	52.	Wing Nuts
		53.	Cylinder Panel
		54.	Fuel Guage
		55.	Liquid Propane Cylinder
		56.	Cylinder Glides
		57.	1/4-20 x 1 3/4 bolts

A-7

Image 7

Weber Liquid Propane Grill, 55052 0100 manual

Contents

Gas Grill Liquid Propane GAS Units only South Hicks Road Customer Service CenterPalatine, IL Contents Storage For Installation in CanadaOperating Genesis Silver-C LP Page Page Page Page Assemble frame Assemble wheel frame Add front panel Continue frame assemblyComplete frame assembly You will need caster frame and wheel frame Insert casters Add cooking box assembly Frame brace2 Install cylinder panelAdd fuel gauge Check that all burner valves are off Install igniterYou will need burner control knobs Install the slide out bottom tray Install manifold bracketYou will need manifold bracket You will need lid, two hair pin cotters1 and two hinge pins2 Install Lid Right swing-up work surface Install the right end trim piece with tool holders Board Do not use the swing-up work surface as a cutting You will need side burner Install side burner Shown, do not push the trim piece in all Install the left end trim piece and swing-up workWay and do not add bolts yet You will need work surface Install the work surfaceDo not use the work surface as a cutting board Closed. Close by turning clockwise Connection. Using a wrench could damageFill liquid propane cylinder Regulator coupling and could cause a gas leak Leaks. Sparks or open flames will result Do not use an open flame to check for gasLeaks. Be sure there are no sparks or open Flames in the area while you check for You will need Thermometer Install the thermometerYou will need Bottom shelf To Extinguish LightingSummary lighting instructions are on the control panel Manual Lighting Lighting only the side burner Lighting the Side Burner Cooking CleaningStorage and/or Nonuse Removal of the LP cylinder Refilling the Liquid Propane CylinderImportant LP Cylinder Information Liquid Propane Cylinder To Connect the hose to the cylinder Liquid Propane LP Cylinders Safe handling tips for Liquid Propane Gas CylindersLiquid Propane Cylinder requirements Inspection and Cleaning of the Weber Spider Stopper Guards Annual Maintenance Main Burner Cleaning Procedure General MaintenanceWeber Spider Stopper Guards Replacing Main Burners Crossover Ignition System Operations Orange flame, in conjunction with Barbecue temperature onlyFlame is low when burner is on Burners burn with a yellow or Conjunction with the smell of gas Side Burner does not lightFlame is low in High position Flame is very yellow