Manuals / Weber / Outdoor Cooking / Gas Grill

Weber Platinum C manual Side Burner Maintenance, mWARNING All gas controls and supply valves

Models: Platinum C

1 30

Page 29

Side Burner Maintenance

mWARNING: All gas controls and supply valves		The Platinum Series II side burner has been factory
should be in the OFF position.		set for the correct air and gas mixture. The correct
Make sure black wire is connected between igniter and		flame pattern is shown.
electrode. Make sure white wire is connected between		1) Tips occasionally flicker yellow
igniter and ground. Check that igniter lock nut is tight.		2)	Light blue
Note - If the igniter works loose, carefully tighten the		3)	Dark blue
igniter lock nut with an adjustable wrench or pliers.
1)	Burner Control Knob
2)	Igniter Button		(1)
3)	Igniter Lock Nut
			(2)
4)	White Wire
5)	Ground		(3)
6)	Black Wire
7)	Electrode

(1)

(2)

(3)

(4)

(5)	(7)
	(7)
	(6)

D-12

Page 29

Image 29

Weber Platinum C manual Side Burner Maintenance, mWARNING All gas controls and supply valves, should be in the OFF position

Contents

2. Extinguish any open flames 3. Open lid m DANGER If you smell gas 1. Shut off gas to the appliancem WARNING THIS GAS APPLIANCE IS DESIGNED FOR OUTDOOR USE ONLYto property m DANGERm WARNINGS Customer Service Center WarrantyWEBER-STEPHEN PRODUCTS CO 250 South Hicks RoadContents For Installation in Canada Gas Supply TestingGeneral Instructions StorageGenesis Platinum-C NG Page Page packaging requires at least two people Remove Packaging from GrillRemove Grill from Lower Packaging A-10 holder2, catch pan and one disposable drip pan Assembly InstructionsYou will need the slide out bottom tray1, catch pan Installing the Warm-Up Basket Install Flavorizer Bars and Cooking GratesYou will need five Flavorizer Bars and two cooking You will need Warm-Up BasketInstall Left Work Surface Installing Work Surfaces, Side Burner Gas Connection GuidelinesInstall Side Burner Assembly Check that all burner valves are offOMMEND THAT THIS INSTALLATION BE DONE BY codes regulating outdoor gas barbecue installaNote - Contact your local municipality for building tions. In absence of Local Codes, you must conm DANGER Check for gas leaksDo not use an open flame to check for gas leaks. Be sure there are no sparks or openyou should recheck all fittings for leaks before using been flame-tested. As a safety precaution howeverCheck for gas leaks Note - All factory-made connections have beenReinstall control panel after checking for gas leaks To Extinguish LightingFailure to open the lid while igniting the barbecue’s burners, or not waiting 5 minFailure to open lid while igniting the Manual LightingTo Extinguish m DANGERgas to clear if the side burner does not light Lighting the Side Burnermay result in an explosive flame-up which can cause serious bodily injury or deathCooking CleaningStorage Note The temperature inside your cooking box for theIMPORTANT NOTE Ambient temperature, type and Using the Smoker Boxsize of wood, moisture content and wind condition will mend using the FireSpice Chips because they igniteInspection and Cleaning of the Weber Annual Maintenanceflames in the area while you check for leaks. Sparks or flames will result in a fireMain Burner Cleaning Procedure General Maintenancesymptoms may result in a fire, which can Main Burner Flame Patternpositioned properly over the valve orifices2 Replacing Main Burnersm CAUTION The burner openings1 must be fit tightly, contact the Customer Service Represen Crossover Ignition System Operationstative in your region using the contact information m WARNING After reinstalling the gas lines, theyProblem TroubleshootingCheck CureProblem Side Burner TroubleshootingCheck Cureigniter lock nut with an adjustable wrench or pliers Side Burner MaintenancemWARNING All gas controls and supply valves should be in the OFF positionTo Reassemble the Burner Head To Clean the Burner Headring. Only clean with a cloth and soap and water mCAUTION Do not enlarge the slots in the burner

Side Burner Maintenance

mWARNING: All gas controls and supply valves

should be in the OFF position.

Note - If the igniter works loose, carefully tighten the

igniter lock nut with an adjustable wrench or pliers.