CABLE ASSEMBLY | 17 |
|
|
|
|
|
|
|
|
| |
|
|
|
|
| 38 |
17. |
|
| 3 |
| 50 |
IMPORTANT: While assembling the cables, |
|
|
|
|
|
do not overtighten the locknuts attaching |
|
|
|
| 70 |
the pulleys; the pulleys must be able to |
|
|
|
| |
|
|
|
| 34 | |
turn freely. Refer to the CABLE DIAGRAMS |
|
| 34 |
| |
|
|
|
| ||
and CABLE ID CHART on pages 24 and 25 |
|
|
|
|
|
for proper cable routing and help identify- |
|
| 100 | 50 |
|
ing the cables. |
|
| 45 | ||
|
|
|
| ||
Locate the High Cable (45). Route the Cable up | 18 |
|
|
|
|
through the Left Top Frame (3) and around a |
|
|
|
| |
90mm Pulley (38). Attach the Pulley inside the |
| 91 | 38 |
|
|
Top Frame with an M10 x 70mm Bolt (100), two |
|
|
| ||
|
|
|
| ||
M10 Washers (50), two 13mm Spacers (34), and |
| 34 |
| 70 |
|
an M10 Nylon Locknut (70). | 50 | 50 |
| ||
|
|
| |||
|
|
|
| ||
18. Route the High Cable (45) around a 90mm Pulley | 100 |
|
|
| 45 |
|
| 34 | |||
(38) and down through the Left Top Frame (3). |
|
|
| ||
|
|
|
|
| |
Attach the Pulley and a Cable Trap (91) inside |
|
|
|
| 3 |
the Top Frame with an M10 x 70mm Bolt (100), |
|
|
|
|
|
two M10 Washers (50), two 13mm Spacers (34), |
|
| 71 |
|
|
and an M10 Nylon Locknut (70). Be sure the |
|
|
|
| |
Cable Trap is turned to hold the Cable in the |
|
| Loosen |
| |
|
|
|
|
| |
groove of the Pulley. |
|
|
|
|
|
Note: To complete this step, it may be neces- | 19 |
|
|
|
|
sary to loosen the indicated M8 Nylon |
|
|
|
|
|
Locknuts (71). Retighten the Locknuts when |
|
|
|
|
|
this step is completed. |
|
|
|
|
|
19. Wrap the High Cable (45) around a 90mm Pulley |
|
|
|
|
|
(38). Attach the Pulley to the single hole side of a |
|
|
|
|
|
Double |
|
|
|
| 45 |
Bolt (66) and an M10 Nylon Locknut (70). |
|
|
|
| |
|
|
|
|
| |
|
|
|
|
| 38 |
|
|
|
|
| 70 |
|
|
| 66 | 56 | |
20. Note: The following drawings are shown from | 20 |
|
|
|
|
the left side of the weight system, with the |
|
|
|
| |
|
|
|
| 70 | |
Left Top Frame (3) removed for clarity. |
|
|
|
| |
|
|
|
|
| |
Wrap the High Cable (45) around a 90mm Pulley |
|
|
|
| 38 |
(38). Attach the Pulley at the rear hole, inside of |
|
|
|
| |
|
|
|
|
| |
the bracket on the Center Top Frame (14) with an |
|
|
| 14 | 45 |
M10 x 45mm Bolt (66) and an M10 Nylon Locknut |
|
|
| ||
|
|
|
| ||
|
|
|
|
| |
(70). |
|
| 66 |
|
|
|
|
|
|
| |
11
