Manuals / Weider / Fitness & Sports / Home Gym

Weider 831.159822 user manual Screw 68. Do not fully tighten the Screw

Models: 831.159822

1 32

Download 32 pages 56.25 Kb

Page 20

Screw (68). Do not fully tighten the Screw.

53. Insert the two Locking Pins (53) into the Butterfly	53
Frame (9). Attach the tether on the Pins to the	53
Frame (9). Attach the tether on the Pins to the		53
Butterfly Frame with an M4 x 10mm Self-tapping		53
Butterfly Frame with an M4 x 10mm Self-tapping
Screw (68). Do not fully tighten the Screw.
		68
	9	53
		53

54.Make sure that all parts have been properly tightened. The use of all remaining parts will be explained in ADJUSTMENTS, starting on the following page.

Before using the weight system, pull each cable a few times to make sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly, find and correct the problem. IMPORTANT: If the cables are not properly routed, they may be damaged when heavy weight is used. See the CABLE DIAGRAM on pages 24 and 25 of this manual for proper cable routing. If there is any slack in the cables, you will need to remove it by tightening the cables; see TIGHTENING THE CABLES on page 22.

20

Image 20

Weider 831.159822 user manual Screw 68. Do not fully tighten the Screw

Contents

WEIGHT SYSTEM EXERCISER User’s Manual Sears, Roebuck and Co., Hoffman Estates, ILTABLE OF CONTENTS IMPORTANT PRECAUTIONS Keep hands and fingers clear of this areaBEFORE YOU BEGIN For help identifying small parts, use the PART IDENTIFICATION CHART ASSEMBLYFRAME ASSEMBLY Do not tighten the M8 Nylon Locknuts 71 yet Do not tighten the M8 Nylon Locknuts 71 yetDo not tighten the M8 Nylon Locknuts 71 yet Do not tighten the M8 Nylon Locknuts 71 yetAttach the Left Top Frame 3 to the Left Upright ARM ASSEMBLY Tighten all of the M8 Nylon Locknuts 71 used in stepsButterfly Frame must be able to pivot easily Bracket must be able to pivot easilyNylon Locknut 70. Do not overtighten the CABLE ASSEMBLY Locknut the Weight Tube should be able to pivot in the “U”-Bracket Note Do not completely tighten the Locknut it should be threaded only two turns onto the end of the Cable, as shown in the inset draw- ing 29. Wrap the Butterfly Cable 46 around a “V”-Pulley 39. Attach the Pulley and a Long Cable Trap31. Wrap the Butterfly Cable 46 around a “V”-Pulley 39. Attach the Pulley and a Long Cable Trap33. Locate the Leg Lever Cable 96. Route the eyelet end of the Cable through the Right Leg 73 and attach it to the Leg Lever 4 with an M8 x 20mm Shoulder Bolt 78 and an M8 Nylon Locknut 39. Route the Low Cable 47 through the Left Leg Page Tabs 46. Wrap the Low Cable 47 around a 90mm PulleySmall SEAT ASSEMBLY Repeat this step with the other Seat 16 andthe Left Seat Frame not shown Repeat this step with the other BackrestScrew 68. Do not fully tighten the Screw ADJUSTMENTS ADJUSTING THE LEG PRESS PLATE TIGHTENING THE CABLESWEIGHT RESISTANCE CHART CABLE DIAGRAMS Butterfly CableHigh Cable Low CableCABLE ID CHART 46 47 3/7” 96 95 1/2” 95 148 1/4” 47 276 3/4” Leg Press CableLeg Lever Cable 45 116 3/4”EXERCISE GUIDELINES Weight LossTHE FOUR BASIC TYPES OF WORKOUTS Muscle Building ToningMUSCLE CHART COOLING DOWNSTAYING MOTIVATED N A O B P C Q D R ES F L T G M H U I JW KPART IDENTIFICATION CHART-Model No. 831.159822 R0103A M8 x 65mm Bolt M6 x 65mm Screw M10 x 60mm Bolt M10 x 55mm Bolt M10 x 50mm BoltM10 x 45mm Bolt M8 x 45mm Bolt M8 x 20mm Shoulder Bolt M4 x 20mm Self-tapping ScrewDescription PART LIST-Model NoDescription EXPLODED DRAWING-Model No R0103A71 34 8050FULL 90 DAY WARRANTY Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL