CABLE ASSEMBLY
17. Route the Medium Cable (58) around the | 17 |
|
| |
3 1/2Ó Pulley (15) attached to the bracket on |
|
| ||
55 | 15 | 12 | ||
the Top Frame (55). Tighten the 3/8Ó x 2Ó Bolt | ||||
|
| |||
(12) and the 3/8Ó Nylon Locknut (21). (Note: | Bracket |
|
| |
This Pulley is |
|
| 58 | |
shown disassembled for easy part identifica- |
|
|
| |
tion.) Be sure that the Cable is in the |
|
|
| |
groove of the Pulley and that the Cable |
|
|
| |
and Pulley move smoothly. |
|
|
| |
18. Remove the 3 1/2Ó Low Pulley (95) from the | 21 |
|
| |
Press Frame (17). Reattach the Pulley with |
|
| ||
|
|
| ||
the 5/8Ó x 9/16Ó Spacer (7) between the |
|
|
| |
Pulley and the Press Frame. |
|
|
| |
the 3/8Ó Nylon Locknut (21). | 18 |
|
| |
|
|
| ||
Locate the Short Cable (23). Route the |
|
|
| |
Short Cable under the 3 1/2Ó Low Pulley (95). | 15 | 23 | 9 | |
Be sure that the end of the Cable with the | ||||
|
| |||
ball is on the indicated side of the Press | 21 |
| 88 | |
Frame (17) and that the Cable is between |
| |||
| Ball | |||
the Pulley and the crossbar on the Press |
|
| ||
|
|
| ||
Frame. Tighten the 3/8Ó Nylon Locknut (21) |
|
| 7 | |
and 3/8Ó x 3 3/4Ó Bolt (88). |
|
| ||
42 |
| 95 | ||
|
| |||
| Crossbar 21 | |||
Route the Short Cable (23) around the 3 1/2Ó |
| |||
17 |
|
| ||
Pulley (15) attached to the lower hole in the |
|
| ||
|
|
| ||
Front Upright (42). Be sure that the Cable |
|
|
| |
Trap (not shown) is turned to hold the |
|
|
| |
Cable in place and that the Cable is routed | 19 |
|
| |
around the Pulley as shown. Tighten the |
|
| ||
15 |
|
| ||
3/8Ó Nylon Locknut (21) and 3/8Ó x 3 3/4Ó Bolt |
|
| ||
23 | 15 |
| ||
(not shown). |
| |||
| 21 |
| ||
|
|
| ||
19. Route the Short Cable (23) around the 3 1/2Ó | 21 | 66 |
| |
Pulley (15) attached to the upper hole in the |
| 12 |
| |
Press Frame (17). Be sure that the Cable |
| 9 | 3 | |
Trap (66) is in the Ò3 oÕclockÓ position and |
| |||
42 | 6 |
| ||
that the Cable is routed around the Pulley |
| |||
|
|
| ||
as shown. Tighten the 3/8Ó Nylon Locknut |
|
|
| |
(21) and 3/8Ó x 3 1/2Ó Bolt (not shown). | 17 |
|
| |
|
|
| ||
Route the Short Cable (23) around the 3 1/2Ó |
|
|
| |
Pulley (15) attached to the upper hole in the |
|
|
| |
Front Upright (42). Be sure that the Cable | 20 |
|
| |
Trap (not shown) is turned to hold the |
|
|
| |
Cable in place and that the Cable is routed |
|
|
| |
around the Pulley as shown. Tighten the |
|
|
| |
3/8Ó Nylon Locknut (21) and 3/8Ó x 3 3/4Ó Bolt |
|
|
| |
(not shown). |
|
|
| |
20. Attach the end of the Short Cable (23) to the | 2 | 57 |
| |
|
| |||
Long |
|
|
| |
Locknut (2) and a 1/4Ó Flat Washer (10). Do | 10 |
|
| |
not tighten the 1/4Ó Nylon Locknut. It |
| 23 |
| |
should be threaded onto the Cable only a |
|
| ||
couple of turns. |
|
|
| |
10
