CABLE ASSEMBLY
20. Wrap the Butterfly Cable (88) around a 3 1/2Ó | 20 |
|
|
|
Pulley (82) as shown. Attach the Pulley and a |
|
|
| |
|
|
|
| |
Cable Trap (80) to the bracket on the Press |
|
|
| 42 |
Upright (4) with a 3/8Ó x 2Ó Bolt (50) and a |
|
|
| |
|
|
| 4 | |
3/8Ó Nylon Locknut (42). The Cable Trap |
|
| 82 | |
must be oriented as shown and be posi- |
|
|
| |
|
|
|
| |
tioned to hold the Cable in the groove of |
|
|
|
|
the Pulley. |
|
| 50 |
|
|
|
|
| |
|
|
| 80 |
|
|
|
| 88 |
|
21. Locate one of the preassembled pairs of | 21 |
|
|
|
Pulley Plates (31) and 3 1/2Ó Pulleys (82). |
|
|
| |
|
|
|
| |
Route the Butterfly Cable (88) under the indi- |
|
|
|
|
cated 3 1/2Ó Pulley (82). The end of the Pulley |
| 88 |
|
|
Plates (31) with two holes should be down- |
|
| 88 | |
|
|
| ||
ward. Be sure that the Cable is between |
|
|
|
|
the Cable Trap (80) and the Pulley, and that |
|
|
|
|
the Cable Trap is positioned to hold the | 82 |
|
|
|
Cable in place. Refer to the inset drawing. |
| 50 |
| |
|
| 80 | ||
|
|
|
| |
Tighten the 3/8Ó x 2Ó Bolt (50) and the 3/8Ó |
|
| End with |
|
|
| two holes |
| |
Nylon Locknut (not shown). | 31 |
|
| |
| should be |
| ||
|
|
| down |
|
22. Wrap the Butterfly Cable (88) around a 3 1/2Ó | 22 |
|
|
|
Pulley (82) as shown. Attach the Pulley and a |
|
|
| |
|
| 80 |
| |
Cable Trap (80) to the other side of the bracket |
|
| 50 | |
on the Press Upright (4) with a 3/8Ó x 2Ó Bolt |
|
|
| |
|
|
|
| |
(50) and a 3/8Ó Nylon Locknut (42). The |
|
| 42 |
|
Cable Trap must be oriented as shown and |
|
| 88 | |
|
| 82 | ||
be positioned to hold the Cable in the |
|
| ||
|
|
| ||
|
|
|
| |
groove of the Pulley. |
|
| 4 |
|
23. Note: The Left Fly Arm (6) is shown | 23 |
|
|
|
removed for easier part identification. |
|
|
| |
|
|
|
| |
Insert a 5/16Ó x 1Ó Bolt (51) through the brack- |
|
| 90 |
|
et on the Left Fly Arm. Fully tighten a 5/16Ó |
|
|
| |
|
|
|
| |
Nylon Jam Nut (90) onto the Bolt. |
| 88 |
|
|
Slide the free end of the Butterfly Cable (88) |
|
|
|
|
onto the 5/16Ó x 1Ó Bolt (51). Thread another |
|
|
|
|
5/16Ó Nylon Jam Nut (90) onto the Bolt. Do |
|
|
| 6 |
not fully tighten the Jam Nut; leave |
| 51 |
| |
|
|
| ||
enough room between the two Jam Nuts |
|
|
|
|
for the Cable to pivot. |
|
|
|
|
12
