FRAME ASSEMBLY
ARM ASSEMBLY
9. | Attach the upper ends of the Short Weight | 9 | 61 |
| 3 61 |
|
|
| Guides (73) to the Top Frame (55) with a 5/16Ó |
|
|
| |||
|
|
|
|
| |||
| x 6Ó Bolt (60), two 1/2Ó x 3/4Ó Spacers (61), and |
|
|
|
|
| 3 |
| a 5/16Ó Nylon Locknut (3). | 60 |
|
|
|
| 55 |
|
|
|
|
|
|
| |
| Attach the upper ends of the Long Weight |
|
|
|
|
|
|
| Guides (62) to the Top Frame (55) with a 5/16Ó |
|
|
|
|
|
|
| x 6Ó Bolt (60), two 1/2Ó x 3/4Ó Spacers (61), and | 73 |
|
| 60 |
|
|
| a 5/16Ó Nylon Locknut (3). |
|
|
|
| ||
|
|
|
|
| 62 |
|
|
10. | Locate and open the parts bag labeled | 10 |
|
| 95 |
| 27 |
| ÒARM ASSEMBLY.Ó |
|
|
| |||
|
|
|
|
| |||
| Be sure there is a Bushing (98) in each side of |
|
|
|
|
| Welded |
|
|
|
|
|
| Tube | |
| the Stabilizer (5). Press a 2Ó Square Inner Cap |
|
|
|
|
| |
|
|
|
|
|
|
| |
| (27) into each end of the Leg Press Arm (96). |
|
|
|
|
| 97 |
|
|
|
| 96 |
|
| |
| Lubricate a 3/8Ó x 3 1/4Ó Bolt (67). Attach the |
|
| 21 | 27 | ||
|
|
|
| ||||
| Leg Press Arm (96) to the Stabilizer (5) with the |
|
|
|
| ||
|
|
|
|
|
|
| |
| Bolt and a 3/8Ó Nylon Locknut (21). Do not over |
|
|
|
|
| 67ÑLubricate |
| tighten the Nylon Locknut. The Leg Press |
|
|
|
|
| |
|
|
|
|
|
|
| |
| Arm must be able to pivot freely. |
|
| 5 | 27 |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
| |
| Align the welded tubes on the Leg Press Plate |
|
|
| 98 |
|
|
| (95) with one set of holes in the Leg Press Arm |
|
|
|
|
| |
|
|
|
|
|
|
| |
| (96). Attach the Leg Press Plate to the Leg | 11 |
|
|
| 17 |
|
| Press Arm with the Press Pin (97). |
|
|
|
| Holes must | |
|
|
|
|
|
|
| be on this |
11. | Press a 1Ó x 7/8Ó Plastic Bushing (90) onto |
|
|
|
|
| side |
|
|
|
|
|
| ||
| each welded spacer on the Press Frame (17). |
|
|
|
|
| 59ÑLubricate |
| Slide the Press Frame into place onto the Base |
|
|
|
|
| |
| (4). Note: This will be a tight fit. The Plastic |
|
|
|
|
|
|
| Bushings should fit on each end of the indi- |
|
|
|
|
|
|
| cated tube in the Base. Make sure that the |
|
|
|
|
|
|
| pulleys are on the side shown. |
|
| 21 |
| Welded Spacers | |
|
|
|
|
| |||
|
|
|
|
|
| ||
| Lubricate the 3/8Ó x 8Ó Bolt (59). Attach the | 4 |
|
|
| 90 |
|
| Press Frame (17) to the Base (4) with the Bolt | Tube |
|
|
|
| |
| and a 3/8Ó Nylon Locknut (21). |
|
|
|
|
| |
|
|
|
|
|
|
| |
9
