![](/images/new-backgrounds/1183413/18341323x1.webp)
CABLE ASSEMBLY
21. Wrap the Butterfly Cable (89) around a 3 1/2” | 21 |
|
|
Pulley (82) as shown. Attach the Pulley and a |
|
| |
|
|
| |
Cable Trap (80) to the bracket on the Leg |
|
| 42 |
Press Upright (4) with a 3/8” x 2” Bolt (50) |
|
| |
|
| 4 | |
and a 3/8” Nylon Locknut (42). The Cable |
| 82 | |
Trap must be oriented as shown and be |
|
| |
|
|
| |
positioned to hold the Cable in the groove |
|
|
|
of the Pulley. |
| 50 |
|
|
|
| |
|
| 80 |
|
|
| 89 |
|
22. Locate one of the preassembled pairs of | 22 |
|
|
Pulley Plates (31) and 3 1/2” Pulleys (82). |
|
| |
|
|
| |
Route the Butterfly Cable (89) under the indi- |
|
|
|
cated 3 1/2” Pulley (82). The end of the Pulley | 89 |
|
|
Plates (31) with two holes should be down- |
| 89 | |
|
| ||
ward. Refer to the inset drawing. Be sure |
|
|
|
that the Cable is between the Cable Trap |
|
|
|
(80) and the Pulley, and that the Cable Trap | 82 |
|
|
is positioned to hold the Cable in place. | 50 |
| |
| 80 | ||
|
| End with | |
Tighten the 3/8” x 2” Bolt (50) and the 3/8” |
|
| |
| two holes |
| |
Nylon Locknut (not shown). | 31 | should be |
|
|
| down |
|
23. Wrap the Butterfly Cable (89) around a 3 1/2” | 23 |
|
|
Pulley (82) as shown. Attach the Pulley and a |
|
| |
| 80 |
| |
Cable Trap (80) to the other side of the bracket |
| 50 | |
on the Leg Press Upright (4) with a 3/8” x 2” |
|
| |
|
|
| |
Bolt (50) and a 3/8” Nylon Locknut (42). The |
| 42 |
|
Cable Trap must be oriented as shown and |
| 89 | |
| 82 | ||
be positioned to hold the Cable in the |
| ||
|
| ||
|
|
| |
groove of the Pulley. |
| 4 |
|
24. Note: The Left Arm (6) is shown removed | 24 |
|
|
for easier part identification. Insert a 5/16” x |
|
| |
|
|
| |
1” Bolt (97) through the bracket on the Left |
| 91 |
|
Arm. Fully tighten a 5/16” Nylon Jam Nut (91) |
|
| |
|
|
| |
onto the Bolt. | 89 |
|
|
Slide the free end of the Butterfly Cable (89) |
|
|
|
onto the 5/16” x 1” Bolt (97). Thread another |
|
|
|
5/16” Nylon Jam Nut (91) onto the Bolt, but |
|
| 6 |
do not fully tighten it. Leave enough room | 97 |
| |
between the two Jam Nuts for the Cable to |
|
|
|
pivot. |
|
|
|
12