8. Raise the Frame (see HOW TO FOLD THE | 8 |
|
|
|
|
|
|
TREADMILL FOR STORAGE on page 15). Be |
| Bracket |
|
|
| ||
careful not to crack the Motor Hood (not |
|
| 87 |
|
| ||
shown). |
|
|
|
|
|
| |
Raise the Gas Spring (76) to a vertical position |
|
| 77 |
|
|
|
|
with the cylinder on the bottom as shown. See |
|
|
|
|
|
| |
the two small inset drawings. Using your fin- |
|
|
|
|
|
| 77 |
gernail or the end of a screwdriver, press on the |
|
| 76 |
|
| ||
end of the Gas Spring Clip (77) to loosen it from |
|
|
|
|
| ||
the Gas Spring. Next, rotate the Gas Spring Clip |
|
|
|
|
| 70 |
|
and pull it out of the Gas Spring. Be careful to |
|
|
|
|
|
| |
avoid losing the Gas Spring Clip. Note: Extra |
|
| Cylinder |
| 77 | ||
Gas Spring Clips are included. |
|
|
| ||||
Then, press the end of the Gas Spring (76) onto |
|
|
|
|
|
|
|
the ball on the bracket on the Frame (87). See |
|
|
|
|
|
|
|
the lower drawing. Insert the Gas Spring Clip |
|
|
|
|
|
|
|
(77) into the two indicated small holes in the end |
|
|
|
|
|
|
|
of the Gas Spring. Then, rotate the Gas Spring |
|
|
|
|
|
|
|
Clip until it clips onto the Gas Spring. |
|
| Bracket |
|
| Holes | |
|
|
|
|
| 77 | ||
|
|
|
|
|
|
| 76 |
9. Position the cylinder end of the Gas Spring (76) | 9 |
|
|
|
|
|
|
near the bracket on the Base (79). | 87 |
|
|
|
|
| |
Remove the Gas Spring Clip (77) from the end |
|
|
|
|
|
| |
of the Gas Spring (76) as described in step 8. If |
|
|
|
|
|
|
|
necessary, rotate the Gas Spring to align the |
|
|
|
| 76 |
|
|
end of the Gas Spring with the ball on the |
|
|
|
|
| 70 | |
bracket on the Base (79). |
|
|
|
|
|
| |
See the lower drawing. Press the end of the |
|
|
|
|
|
|
|
Gas Spring (76) onto the ball on the bracket. |
| 79 |
|
|
|
|
|
Note: It may be necessary to pull the Latch |
| 77 |
|
|
|
| |
Knob (70) to the right and move the Frame |
|
|
|
|
|
| |
(87) forward or backward as you press the |
|
|
|
| Bracket |
| |
Gas Spring onto the ball. |
|
|
|
|
| ||
Next, insert the end of the Gas Spring Clip (77) |
|
|
|
|
|
|
|
into two of the small holes in the end of the Gas |
|
|
|
|
|
|
|
Spring (76). Then, rotate the Gas Spring Clip |
|
|
|
|
|
|
|
until it clips onto the Gas Spring. |
|
|
|
|
|
| 76 |
Lower the Frame (87) to the floor. See HOW TO |
|
|
|
|
|
| |
LOWER THE TREADMILL FOR USE on page 16. |
|
| 77 |
|
|
|
|
Make sure that the four Leveling Feet (not |
|
| Holes |
|
| ||
shown) rest firmly on the floor (see HOW TO |
|
|
|
|
| ||
LEVEL THE TREADMILL on page 14). |
|
|
|
|
|
|
|
10. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of clear plastic on the treadmill decals, remove the plastic. To protect the floor or carpet, place a mat under the tread- mill. Note: Extra hardware may be included. Keep the included hex keys in a secure place; one of the hex keys is used to adjust the walking belt (see page 18).
10
