Location Requirements

Site location

Select a location near the center of the water piping system. It must be installed indoors and in a vertical position on a level surface, in an area where water leakage will not cause consequential damage.

The water heater should be located in an area not subject to freezing temperatures. Water heaters located in unconditioned spaces (i.e., attics, garages, base- ments, etc.) may require the water piping and drain piping to be insulated to protect against freezing. The drain and controls must be easily accessible for opera- tion and service.

Keep combustibles such as boxes, magazines, clothes, etc., away from the water heater area.

Do not use this water heater in conjunction with a spa or hot tub.

IMPORTANT: The water heater should be located in an area where leakage of the tank or connections will not result in damage to the area adjacent to the water heater or to lower floors of the structure. Due to the normal corrosive action of the water, the tank will eventually leak after an extended period of time. Also, any external plumbing leak, including those from improper installation, may cause early failure of the water tank due to corrosion if not repaired. If the homeowner is uncomfortable with making the repair, a qualified person should be contacted. A suitable metal drain pan should be installed under the water heater as shown below. This metal drain pan is to protect the property from damage which may occur from normal condensate formation on the tank or leaks in the tank and pipe connections. The metal drain pan must limit the water level to a maximum depth of 2-1/2 inches and be two inches wider than the heater and piped to an adequate drain. Locate the water heater near a

suitable indoor drain. Outdoor drains are subject to freezing temperatures which can obstruct the drain line. The piping should be at least 3/4”ID and pitched for proper drainage.

Under no circumstance will the manufacturer or seller of this water heater be held liable for any water damage that is caused by your failure to follow these instructions.

2 1/2” Max

Pipe to adequate drain

At least 2” inches greater than the diameter of the water

heater.

Figure 1

NOTE: Local codes and requirements in your area may require the water heater to be installed such that the bottom element is elevated from the floor at least 18 inches.

NOTE: The water heater shall be located so it is not subject to physical damage by moving vehicles or area flooding.

Figure 2

Residential Garage

Installation

Vehicle

Stop

Drain

Metal Drain Pan

State of California

NOTE: The water heater must be braced, anchored, or strapped to avoid moving during an earthquake. Contact local utilities for code requirements in your area or call 1-877-817-6750and request instructions.

4

Page 3 Page 5
Page 4
Image 4
Whirlpool 318686-000 installation instructions Location Requirements, Site location
Page 3 Page 5

318686-000 specifications

The Whirlpool 318686-000 is a highly regarded appliance part that plays an essential role in modern kitchen functionality. Designed with the user in mind, it boasts several features and technologies that enhance its performance and reliability.

One of the primary characteristics of the Whirlpool 318686-000 is its compatibility with a wide range of Whirlpool ovens and ranges, making it a versatile choice for many households. This part is commonly known as the surface element, which provides the necessary heat for cooking a variety of dishes. Its design ensures even heat distribution, which is vital for achieving perfectly cooked meals every time.

The Whirlpool 318686-000 is engineered with durability in mind. Constructed from high-quality materials, this part is built to withstand the daily stresses of cooking while maintaining its performance. This longevity translates into reduced replacement costs and increased satisfaction for users, making it an economical choice for homeowners.

In terms of safety, the Whirlpool 318686-000 features advanced technology to minimize risks associated with cooking. It typically includes integrated thermal protection, which helps prevent overheating. This feature not only prolongs the lifespan of the component but also ensures a safer cooking environment for users.

Installation of the Whirlpool 318686-000 is designed to be user-friendly. Homeowners can replace this part without needing specialized tools or professional assistance, allowing for convenient maintenance. This ease of installation is especially appealing for those who prefer a DIY approach to home repairs.

Efficiency is another hallmark of the Whirlpool 318686-000. The design optimizes energy consumption, allowing users to cook efficiently while saving on utility costs. The element heats up quickly, reducing wait times and enhancing overall cooking experiences.

Whirlpool is a brand synonymous with innovation, and the 318686-000 reflects this commitment to excellence. The part combines modern technology with practical design, ensuring it meets the needs of contemporary cooking. With its blend of durability, safety, efficiency, and ease of use, the Whirlpool 318686-000 is an essential addition to any kitchen, providing reliable performance that cooks can depend on for years to come. Whether replacing a worn-out part or upgrading to enhance cooking capabilities, this surface element is a top choice for Whirlpool appliance users.
Top Page Image Contents