6.Connect the black power wire from the home’s electri- cal service to the heater’s TWO black wires and secure with the appropriate size wire nut. When you are done, you will have THREE black wires under one wire nut.

7.Locate and connect the remaining power wire (usu- ally red, but in your home this wire may be some other color) from the home’s electrical service to the water heater’s TWO red wires and secure with the appro priate size wire nut. When you are done, you will have THREE red wires under one wire nut (depending on the actual color of your home’s electric wiring).

8.Replace the junction box cover and secure with the screw removed in step 2.

9.Do not remove the Smart Grid cover from the Smart Grid connector (Figure 8A) unless this feature is be- ing used (see the “Smart Grid Technology” section this manual).

10.Insure that the water heater is completely full of water. Proceed to water heater start up in the “Operating Your Water Heater” section of this manual.

INSTALLATION CHECKLIST

Water Heater Location

□Centrally located with the water piping system.

□The flooring beneath the water heater must be able to support the weight of the water heater when filled with water.

□Located indoors and in a vertical position. Protected from freezing temperatures.

□Provisions made to protect the area from water damage. Metal drain pan installed and piped to an adequate drain.

□Sufficient room to service the water heater.

□The site location must be free from any corrosive elements in the atmosphere such as sulfur, fluorine, and chlorine. These elements are found in aero- sol sprays, detergents, bleaches, cleaning solvents, air fresheners, paint, and varnish removers, refriger- ants, and many other commercial and household products.

Water System Piping

□Temperature and pressure relief valve properly installed with a discharge pipe run to an adequate drain and protected from freezing (See Figure 3).

□All piping properly installed and free of leaks.

□Suitable metal drain pan lines installed and piped to an adequate drain (See Figure 3).

□Heater completely filled with water (See Figure 3).

□Closed system pressure buildup precautions installed (See “Closed System/Thermal Expansion” section).

□Mixing valve (when applicable) installed per manufac- turer’s instructions (see Figure 4).

Electrical Connections

□Wiring and connections comply with all applicable codes.

□Water heater and electrical supply are properly grounded.

□Proper overload fuse or circuit breaker protection installed.

9

Page 8 Page 10
Page 9
Image 9
Whirlpool 318686-000 Installation Checklist, Water Heater Location, Water System Piping, Electrical Connections
Page 8 Page 10

318686-000 specifications

The Whirlpool 318686-000 is a highly regarded appliance part that plays an essential role in modern kitchen functionality. Designed with the user in mind, it boasts several features and technologies that enhance its performance and reliability.

One of the primary characteristics of the Whirlpool 318686-000 is its compatibility with a wide range of Whirlpool ovens and ranges, making it a versatile choice for many households. This part is commonly known as the surface element, which provides the necessary heat for cooking a variety of dishes. Its design ensures even heat distribution, which is vital for achieving perfectly cooked meals every time.

The Whirlpool 318686-000 is engineered with durability in mind. Constructed from high-quality materials, this part is built to withstand the daily stresses of cooking while maintaining its performance. This longevity translates into reduced replacement costs and increased satisfaction for users, making it an economical choice for homeowners.

In terms of safety, the Whirlpool 318686-000 features advanced technology to minimize risks associated with cooking. It typically includes integrated thermal protection, which helps prevent overheating. This feature not only prolongs the lifespan of the component but also ensures a safer cooking environment for users.

Installation of the Whirlpool 318686-000 is designed to be user-friendly. Homeowners can replace this part without needing specialized tools or professional assistance, allowing for convenient maintenance. This ease of installation is especially appealing for those who prefer a DIY approach to home repairs.

Efficiency is another hallmark of the Whirlpool 318686-000. The design optimizes energy consumption, allowing users to cook efficiently while saving on utility costs. The element heats up quickly, reducing wait times and enhancing overall cooking experiences.

Whirlpool is a brand synonymous with innovation, and the 318686-000 reflects this commitment to excellence. The part combines modern technology with practical design, ensuring it meets the needs of contemporary cooking. With its blend of durability, safety, efficiency, and ease of use, the Whirlpool 318686-000 is an essential addition to any kitchen, providing reliable performance that cooks can depend on for years to come. Whether replacing a worn-out part or upgrading to enhance cooking capabilities, this surface element is a top choice for Whirlpool appliance users.
Top Page Image Contents