Burner ports: Check burner flames occasionally for proper size and shape as shown above. A good flame is blue in color, not yellow. Keep this area free of soil and do not allow spills, food, cleaning agents or any other material to enter the burner ports.
To Clean:
IMPORTANT: Before cleaning, make sure all controls are off and the oven and cooktop are cool. Do not use oven cleaners, bleach or rust removers.
1.Remove the burner cap from the burner base and clean according to “General Cleaning” section.
2.Clean the gas tube opening with a damp cloth.
3.Clean clogged burner ports with a straight pin as shown. Do not enlarge or distort the port. Do not use a wooden toothpick. If the burner needs to be adjusted, contact a trained repair specialist.
4.Replace the burner cap, making sure the alignment pins are properly aligned with the burner cap.
A
B
A.Incorrect
B.Correct
5.Turn on the burner. If the burner does not light, check cap alignment. If the burner still does not light, do not service the sealed burner yourself. Contact a trained repair specialist.
Home Canning
When canning for long periods, alternate the use of surface cooking areas, elements or surface burners between batches. This allows time for the most recently used areas to cool.
■Center the canner on the grate or largest surface cooking area or element. Canners should not extend more than 1" (2.5 cm) outside the cooking area.
■Do not place canner on 2 surface cooking areas, elements or surface burners at the same time.
■On ceramic glass models, use only
■On coil element models, the installation of a Canning Unit Kit is recommended. If a kit is not installed, the life of the coil element will be shortened. See “Assistance or Service” for ordering instructions.
■For more information, contact your local U.S. Government Agricultural Department Extension Office. In Canada, contact Agriculture Canada. Companies that manufacture home canning products can also offer assistance.
Cookware
IMPORTANT: Do not leave empty cookware on a hot surface cooking area, element or surface burner.
Ideal cookware should have a flat bottom, straight sides and a
Rough finishes may scratch the cooktop. Aluminum and copper may be used as a core or base in cookware. However, when used as a base they can leave permanent marks on the cooktop or grates.
Cookware material is a factor in how quickly and evenly heat is transferred, which affects cooking results. A nonstick finish has the same characteristics as its base material. For example, aluminum cookware with a nonstick finish will take on the properties of aluminum.
Cookware with nonstick surfaces should not be used under the broiler.
Use the following chart as a guide for cookware material characteristics.
COOKWARE | CHARACTERISTICS | |
|
| |
Aluminum | ■ Heats quickly and evenly. | |
| ■ Suitable for all types of cooking. | |
| ■ Medium or heavy thickness is best for | |
|
| most cooking tasks. |
|
| |
Cast iron | ■ Heats slowly and evenly. | |
| ■ Good for browning and frying. | |
| ■ Maintains heat for slow cooking. | |
|
|
|
Ceramic or | ■ | Follow manufacturer’s instructions. |
Ceramic glass | ■ Heats slowly, but unevenly. | |
| ||
| ■ Ideal results on low to medium heat | |
|
| settings. |
|
| |
Copper | ■ Heats very quickly and evenly. | |
|
|
|
Earthenware | ■ | Follow manufacturer’s instructions. |
| ■ Use on low heat settings. | |
|
| |
Porcelain | ■ See stainless steel or cast iron. | |
|
| |
steel or cast |
|
|
iron |
|
|
|
| |
Stainless steel | ■ Heats quickly, but unevenly. | |
| ■ A core or base of aluminum or copper | |
|
| on stainless steel provides even |
|
| heating. |
|
|
|
7
