LocationRequirements

Selecting the proper location for your washer improves performance and minimizes noise and possible washer “walk.”

Your washer can be installed under a custom counter, or in a basement, laundry room, closet, or recessed area. See “Drain System.”

Companion appliance location requirements should also be considered. Proper installation is your responsibility.

You will need

A water heater set to deliver 120°F (49°C) water to the washer.

A grounded electrical outlet located within 6 ft (1.8 m) of where the power cord is attached to the back of the washer. See “Electrical Requirements.”

Hot and cold water faucets located within 4 ft (1.2 m) of the hot and cold water fill valves, and water pressure of 20-100 psi (137.9-689.6 kPa).

A level floor with a maximum slope of 1" (2.5 cm) under entire washer. Installing the washer on soft floor surfaces, such as carpets or surfaces with foam backing, is not recommended.

A sturdy and solid floor to support the washer with a total weight (water and load) of 400 lbs (180 kg).

Do not operate your washer in temperatures below 32°F (0°C). Some water can remain in the washer and can cause damage in low temperatures.

Installation clearances

The location must be large enough to allow the washer door to be fully opened.

Additional spacing should be considered for ease of installation and servicing.

Additional clearances might be required for wall, door, and floor moldings.

Additional spacing of 1" (2.5 cm) on all sides of the washer is recommended to reduce noise transfer.

Companion appliance spacing should also be considered.

Washer Dimensions

27"

51" (68.6 cm) (129.5 cm)

38"

(96.5 cm)

Recommended installation spacing for custom undercounter installation

The dimensions shown are for the recommended spacing.

Custom undercounter installation - Washer only

39" min. (99.0 cm)

1"

 

27"

 

1"

(2.5 cm)

(68.6 cm)

(2.5 cm)

Recommended installation spacing for recessed or closet installation, with or without a pedestal

The dimensions shown are for the recommended spacing.

Recessed area or closet installation

 

 

 

 

3"

 

 

 

 

(7.6 cm)

 

 

34"

48 in.2 *

 

 

(86.4 cm)

(310 cm2)

 

 

 

 

24 in.2 *

3"

 

 

 

(155 cm2)

 

 

 

 

(7.6 cm)

1"

31¹⁄₂"

4"

 

 

(2.5 cm)

(80 cm)

(10.2 cm)

 

 

A

 

 

B

A. Side view - closet or confined area

B. Closet door with vents

*Min. top and bottom air openings for closet door.

Recessed or closet installation - Washer on pedestal

 

 

 

 

18" min.

 

 

 

 

 

(45.7 cm)

 

1"

27"

1"

1"

31¹⁄₂"

4"

(2.5 cm)

(68.6 cm)

(2.5 cm)

(2.5 cm) (80 cm) (10.2 cm)

 

A

 

 

B

 

A. Recessed area

B. Side view - closet or confined area

31¹⁄₂"

(80.0 cm)

5

Page 5
Image 5
Whirlpool W10158200A manual LocationRequirements, Installation clearances, Washer Dimensions

W10158200A specifications

The Whirlpool W10158200A is an innovative appliance designed to enhance modern kitchens with its advanced features and user-friendly characteristics. This product, primarily known as a refrigerator water filter, is engineered to provide cleaner and better-tasting water and ice, making it an essential component for households that prioritize health and convenience.

One of the main features of the W10158200A is its ability to reduce contaminants. This filter effectively eliminates chlorine taste and odor, lead, mercury, and several other impurities, ensuring that the water you use for drinking, cooking, and making ice is as pure as possible. The advanced filtration technology employed in this product not only enhances the quality of water but also improves the flavor, allowing you to enjoy every sip or glass of ice.

Another notable characteristic of the Whirlpool W10158200A is its easy installation process. The filter is designed to fit securely and seamlessly into compatible Whirlpool refrigerators, making it accessible for even those who may not have extensive DIY experience. Additionally, the straightforward replacement process means that maintaining clean water is a hassle-free task. Users can quickly change the filter without special tools, which encourages regular upkeep and ensures optimal performance.

This water filter boasts a considerable lifespan, typically lasting up to six months or filtering about 200 gallons of water, depending on usage. This longevity allows families to enjoy consistent quality without frequent replacements, making it both cost-effective and practical for everyday use.

Moreover, the W10158200A is designed with sustainability in mind. By providing an efficient filtration solution, this product helps reduce the reliance on bottled water, thus contributing to environmental conservation efforts. Using this filter can lead to less plastic waste while still ensuring that your home has access to safe and refreshing water.

In conclusion, the Whirlpool W10158200A stands out due to its advanced filtration capabilities, user-friendly design, sustainable benefits, and longevity. It is a reliable choice for those looking to improve the quality of their drinking water and enhance their culinary experiences. Embracing this innovative solution helps ensure that families enjoy not only the taste but also the peace of mind that comes with quality water.