Whirlpool W10665256D Installation Requirements, Tools and Parts, Location Requirements, KSGG700E

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Optional Parts

To purchase these or any other accessories, please reference the “Accessories” section of the User Guide for contact information.

■ Side Trim Kits:

⁵⁄₈" (1.7 cm) White - Order Part Number W10675027

⁵⁄₈" (1.7 cm) Black - Order Part Number W10675026

Tools Needed

■Tape measure

■Phillips screwdriver

■Flat-blade screwdriver

■¹⁄₈" (3 mm) flat-blade screwdriver

■Level

■Drill

■Wrench or pliers

■Pipe wrench

■¹⁵⁄₁₆" (2.4 cm) combination wrench

■¹⁄₈" (3.2 mm) drill bit (for wood floors)

■Marker or pencil

■Pipe-joint compound resistant to LP gas

■³⁄₁₆" (4.8 mm) carbide-tipped masonry drill bit (for concrete/ceramic floors)

■Noncorrosive leak-detection solution

For LP/Natural Gas

Conversions

■⁵⁄₈" (1.6 cm) combination wrench

■³⁄₈" (1 cm) nut driver

■⁹⁄₃₂" (7 mm) nut driver

■Masking tape

⁵⁄₈" (1.7 cm) Stainless Steel - Order Part Number W10675028

1¹⁄₈" (2.9 cm) White - Order Part Number W10731885

1¹⁄₈" (2.9 cm) Black - Order Part Number W10731886

1¹⁄₈" (2.9 cm) Stainless Steel - Order Part Number

W10731887

■ Backsplash Kits:

High 6" (15.2 cm) White - Order Part Number W10655448

High 6" (15.2 cm) Black - Order Part Number W10655449

High 6" (15.2 cm) Stainless Steel - Order Part Number

W10655450

Location Requirements

IMPORTANT: Observe all governing codes and ordinances. Do not obstruct flow of combustion and ventilation air.

■	It is the installer’s responsibility to comply with installation
	clearances specified on the model/serial/rating plate. The
	model/serial/rating plate is located behind the oven door on
	the top right-hand side of the oven frame.
■	The range should be located for convenient use in the

Parts Supplied

Check that all parts are included.

■LP/Natural Gas Conversion Kit

■#10 x 1⁵⁄₈" (4.1 cm) screws (for mounting anti-tip bracket) (2)

■Anti-tip bracket (inside oven cavity)

Anti-tip bracket must be securely mounted to the back wall or floor. Thickness of flooring may require longer screws to anchor bracket to subfloor. Longer screws are available from your local hardware store.

■For Models:

		KSGG700E
		KSGB900E
		MGS8880D
	WEG730H0D	WEG760H0D	JGS1450D
Burner Caps	5	5	4
Burner Grates	2	2	3
Oven Racks	2	3	3

Parts Needed

Check local codes and consult gas supplier. Check existing gas supply and electrical supply. See “Electrical Requirements” and “Gas Supply Requirements” sections.

IMPORTANT: When the range is used under microwave models: JMC82808CB-0, JMV9196CB-0, or YJMV9196CB-0, the Door Baffle Plate Part Number W10737014 must be ordered and used. Please reference the “Accessories” section of the User Guide for contact information.

kitchen.

■ Recessed installations must provide complete enclosure of

the sides and rear of the range.

■ To eliminate the risk of burns or fire by reaching over the

heated surface units, cabinet storage space located above

the surface units should be avoided. If cabinet storage is to

be provided, the risk can be reduced by installing a range

hood or microwave hood combination that projects

horizontally a minimum of 5" (12.7 cm) beyond the bottom of

the cabinets.

■ All openings in the wall or floor where range is to be installed

must be sealed.

■ Cabinet opening dimensions that are shown must be used.

Given dimensions are minimum clearances.

■ The anti-tip bracket must be installed. To install the anti-tip

bracket shipped with the range, see “Install Anti-Tip Bracket”

section.

■ Grounded electrical supply is required. See “Electrical

Requirements” section.

■ Proper gas supply connection must be available. See “Gas

Supply Requirements” section.

■ Contact a qualified floor covering installer to check that the

floor covering can withstand at least 200°F (93°C).

■ Use an insulated pad or ¼" (0.64 cm) plywood under range if

installing range over carpeting.

IMPORTANT: To avoid damage to your cabinets, check with your builder or cabinet supplier to make sure that the materials used will not discolor, delaminate or sustain other damage. This oven has been designed in accordance with the requirements of UL and CSA International and complies with the maximum allowable wood cabinet temperatures of 194°F (90°C).

4