INSTALLATION REQUIREMENTS

These instructions are intended as a general guide only for use by qualified persons and do not supersede any national or local codes in any way. Compliance with all local, state or national codes pertaining to this type of equipment should be determined prior to installation.

Read this entire instruction manual as well as instructions supplied with separate equipment before starting the installation.

The installation of the whole house dehumidifier must conform to the requirements of the National Fire Protection Association, the National Electrical Code, ANSI/NFPA No. 70 (latest edition) in the United States, and any state laws, local ordinances (including plumbing or wastewater codes). Local authorities having jurisdiction should be consulted before installation is made. Such applicable regulations or requirements take precedence over the general instructions in this manual.

Install the conditioned air plenum, ducts and air filters (not provided) in accordance with NFPA 90B Standard for the Installation of Warm Air Heating and Air-Conditioning Systems (latest edition).

The whole house dehumidifier is designed and approved for indoor use only.

It is recommended that the whole house dehumidifier be matched to the HVAC system to ensure proper operation and efficient performance.

Refer to the rating plates located on the whole house dehumidifier and on the HVAC system.

It is recommended that the whole house dehumidifier be connected to only one existing HVAC system. If there are multiple HVAC systems in the building, use one dehumidifier per system.

ToolsandParts

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Tools Needed

■

Locking pliers

■

Screwdriver

■

Drill and drill bit

■

Tin snips

Parts Needed

■Sheet metal screws or rivets

■Shop-fabricated sheet metal turning vanes, offsets, and transitions, if needed

■Sealant

■Insulated flexible duct

■³⁄₈"-16all-thread rod for suspended applications

■Insulated duct for fresh air ventilation

Parts Supplied

■Grommet plugs (4)

Check local codes and HVAC supplier. Check existing electrical supply, and read “Electrical Requirements” and “Location Requirements” before purchasing parts.

LocationRequirements

■The dehumidifier may be installed on all new or existing furnaces or air handlers used in residential applications.

■The whole house dehumidifier is designed to be located indoors.

■Locate the whole house dehumidifier as close to the return air duct of an existing furnace or air handler as possible to minimize the required ductwork for connecting the dehumidifier to the existing furnace or air handler.

■The location should allow for access to the filter access panel at the front of the dehumidifier for inspection and replacing the filter. See the Minimum Clearance Requirements chart.

■The location must allow for access to the electrical access panel for servicing and maintenance.

■Locate the whole house dehumidifier in an area where the temperature is between 40ºF (4ºC) and 125ºF (52ºC). If the dehumidifier is located in an area of extreme heat or high humidity, additional external insulation may be required to prevent condensation on the exterior of the dehumidifier.

■If the dehumidifier is located above a living area or above an area where water leakage may cause damage (see local codes for other requirements), a secondary drain pan must be installed under the dehumidifier.

■The controls for the whole house dehumidifier are remote from the dehumidifier and must be located in the space that is to be conditioned. The controls are low voltage (24-volt) and should be connected to the dehumidifier with code approved, low voltage thermostat cable.

■If the dehumidifier is located directly on structural building members, use vibration absorbers/eliminators.

Minimum Clearance Requirements

For Optimum Service Access

Front24"

Rear12"

Blower End

12"

Top12"

2

Page 1 Page 3
Page 2
Image 2
Whirlpool WPDH160XS, WGDV160UH, WPDV160XS, WGDH160UH Installation Requirements, ToolsandParts, LocationRequirements
Page 1 Page 3

WPDV160XS, WPDH160XS, WGDV160UH, WGDH160UH specifications

Whirlpool has made a mark in the home appliance sector with its innovative dryers, including the WGDV160UH, WPDV160XS, WPDH160XS, and WGDH160UH models. These dryers not only focus on functionality but also emphasize energy efficiency and user-friendly features, designed to cater to modern laundry needs.

The WGDV160UH is a gas dryer that offers excellent drying performance while being gentle on clothes. It features a large capacity drum, accommodating family-sized loads, which helps save time on laundry days. The advanced moisture sensing technology ensures that clothes are dried evenly and thoroughly, automatically adjusting the drying time based on moisture levels. This feature helps prevent over-drying, preserving the quality of fabrics and saving energy.

In contrast, the WPDV160XS is an electric dryer that shines with its sleek design and efficient performance. It also boasts the same impressive moisture sensing capabilities as the WGDV160UH, making it perfect for users looking to achieve optimal drying results. Additionally, this model comes equipped with multiple drying cycles, allowing users to choose the best setting for different fabric types.

The WPDH160XS is a heat pump dryer, which represents an eco-friendly option for consumers. Using a closed-loop system, it heats air within the dryer, significantly reducing energy consumption compared to traditional dryers. This model is ideal for those who prioritize energy savings without compromising on drying performance. Its user-friendly interface simplifies operation, making laundry tasks more manageable.

Lastly, the WGDH160UH combines the best of both worlds with its gas-powered efficient drying capabilities. Similar to its counterparts, it also features advanced drying technology designed to protect clothes from excessive heat. This model stands out due to its ability to offer quick drying times along with energy-efficient operations.

All four models share a commitment to user convenience, featuring easy-to-use controls and designs that allow for effortless operation. For households looking for reliable and energy-efficient dryers, these Whirlpool models are excellent choices, balancing functionality, energy savings, and convenience in one package. With these dryers, Whirlpool continues its tradition of delivering quality and innovation in home appliances.
Top Page Image Contents