Manuals / Xerox / Computer Equipment / Printer

Xerox 82xx, 83xx manual Adjusting the roll units, No Description

Models: 82xx 83xx

1 44

Download 44 pages 1.37 Kb

Page 34

Image 34

3.3.2.3Adjusting the roll units

Procedure

Step 1 : Use the correct amount of spacers (2) to cover the space between the drawn lines (1).

No Description

1Drawn lines

2Spacer

Step 2 : Determine the deviation of the roll unit using the image and table below.

Adjusting the FRONT Units

IF line 2 lays…THEN…

BEFORE line 1 Remove spacers on the left front unit or add spacers on the right front unit.

BEHIND line 1 Add spacers on the left front unit or remove spacers on the right front unit.

Adjusting the REAR Units

IF line 2 lays…THEN…

BEFORE line 1 Add spacers on the left rear unit or remove spacers on the right rear unit.

BEHIND line 1 Remove spacers on the left rear unit or add spacers on the right rear unit.

3-20

Page 34

Image 34

Xerox 82xx, 83xx manual Adjusting the roll units, No Description

Contents

Xerox 82xx/83xx Wide Format Printer User GuideUnwinder / Winder August2007 by Xerox Corporation. All rights reserved Prepared by Xerox Corporation Global Knowledge and Language Services800 Phillips Road, Bldg. 0218-01A Webster, New York USA trademarks are also acknowledged3-159H TABLE OF CONTENTS4-18 H This page is intentionally left blank Safety terms 1 SAFETY INSTRUCTIONS1.2 IMPORTANT SAFETY INSTRUCTIONS 1.1 INTRODUCTIONFront tensioning label 1.3 OPERATION LABELSFoot switch label PCB box labelWEEE regulations 1.4 WEEE REGULATIONSDisposal of your old product Environmental informationThis page is intentionally left blank 2.1.1 Front / Winder 2 PRODUCT OVERVIEW2.1 PART NAMES AND FUNCTIONS 2.1.2 Rear / UnwinderName 2.1.3 Operation PanelFunction 2.2.1.1 Packaging box 2.2 VERIFYING THE PACKAGED ITEMS2.2.1 For Rockhopper 3, Spitfire and Viper Part DescriptionPart Description 2.2.1.2 Winder kitQuantity Part Description 2.2.2 For ValueJet 1604 series2.2.2.1 Packaging box QuantityPart Description 2.2.2.2 Winder kitQuantity INSTALL THE TENSIONING BARS 3 INSTALLING THE UNIT3.1 GENERAL SEQUENCE ADJUST THE WEIGHT SUPPORTS UNDER THE ROLL UNIT BARSDescription 3.2 INSTALL ALL PARTS3.2.1 Mounting the roll unit bars Quantity neededIF … No. DescriptionDescription THEN …No Description 3.2.2 Mounting the brackets for the tensioning bars3.2.2.1 On a Spitfire, Rockhopper 3 and Viper DescriptionDescription 3.2.2.2 On a ValueJetParts and Tools needed QuantityUse care when lifting the tensioning bars to avoid bending the bars 3.2.3 Installing the tensioning barsProcedure Parts and Tools neededInstall the remaining screws on the left bracket. Tighten all screws Parts and Tools needed 3.2.4 Mounting the PCB BoxProcedure Description3.2.5 Connecting the cables Nr Description3.3.1.1 Checking the calibration 3.3 CALIBRATING THE UW/W3.3.1 Calibrating the rear tensioning system Included in kitStep 4 Check if the edges of the loop are aligned on each other No DescriptionNo Description PART 2 DRAWING THE CONTROL LINESStep 4 Carefully pull the strip to create some tension No Description 3.3.1.2 Adjusting the tensioning systemsNo Description Tool Hexagon wrench 3 mm THEN turn the adjustment screws as followsMake sure to turn both adjustment screws an equal amount of turns IF Line 2 lays…3.3.2.2 Checking the calibration of the roll units 3.3.2 Calibrating the front and rear roll unit bars3.3.2.1 Introduction FRONT VIEWNo Description 1 Synthetic paper strip 2 Loop 3 Core 4 Pressure rollers1 Synthetic paper strip 2 Loop 3 Core 4 Pressure rollers Step 2 Draw a line. See image belowNo Description PART 2 DRAWING THE CONTROL LINESStep 5 Pull the strip so there is an equal tension 3.3.2.3 Adjusting the roll units No DescriptionNo Description 1 Spacer 2 Printer’s stand 3 Roll unit bar3.3.3.2 Location of the weight supports on a 90” printer 3.3.3 Adjusting the weight supports under the UW/W3.3.3.1 Location of the weight supports on a 65” printer Hexagon wrench 3 mmNo Description 3.3.3.3 Adjusting the weight supports1 Hexagon wrench 6 mm 2 Turning direction to lower the support This page is intentionally left blank 3-24 4.1 TURNING THE POWER ON / OFF 4 OPERATING THE SYSTEMMaximum loading capacity 4.2 LOADING ROLL MEDIAMetrical Maximum media widthOutside printable Inside PrintableHINT