Manuals / Xerox / Computer Equipment / Printer

Xerox 82xx Installing the tensioning bars, Parts and Tools needed, Description, Quantity, Step

Models: 82xx 83xx

1 44

Page 20

3.2.3Installing the tensioning bars

Parts and Tools needed

No	Description	Quantity
1	Front tensioning bar	RH3 & SPFR	ValueJet 1604
1	Front tensioning bar	1	1
2	Rear tensioning bar	1	1
3	D-lock type shaft	2	-
4	Pivot shaft	-	2
5	Pan head screw flat M4x10	4	4
6	Philips screwdriver	1	1
7	Hexagon wrench 5 mm	1	1
Procedure
Step 1 :	Insert the two shafts (1) in the left (adjustable) bracket at the front and rear.

	front	rear
	Caution


Use care when lifting the tensioning bars to avoid bending the bars.

Step 2 : Position the front tensioning bar (1) between the D-lock shafts of the left and right bracket in such a way that it fits the corresponding D hole in the plates (2) of the tensioning bars.

–––

Notes

While installing the tensioning bar, push the adjustable shaft in the left bracket, to make insertion of the front tensioning bar possible.

3-6

Page 20

Image 20

Xerox 82xx Installing the tensioning bars, Parts and Tools needed, Description, Quantity, RH3 & SPFR, ValueJet, Procedure

Contents

User Guide Unwinder / WinderXerox 82xx/83xx Wide Format Printer AugustPrepared by Xerox Corporation Global Knowledge and Language Services 800 Phillips Road, Bldg. 0218-01A Webster, New York USA2007 by Xerox Corporation. All rights reserved trademarks are also acknowledged4-18 H TABLE OF CONTENTS3-159H This page is intentionally left blank 1 SAFETY INSTRUCTIONS 1.2 IMPORTANT SAFETY INSTRUCTIONSSafety terms 1.1 INTRODUCTION1.3 OPERATION LABELS Foot switch labelFront tensioning label PCB box label1.4 WEEE REGULATIONS Disposal of your old productWEEE regulations Environmental informationThis page is intentionally left blank 2 PRODUCT OVERVIEW 2.1 PART NAMES AND FUNCTIONS2.1.1 Front / Winder 2.1.2 Rear / UnwinderFunction 2.1.3 Operation PanelName 2.2 VERIFYING THE PACKAGED ITEMS 2.2.1 For Rockhopper 3, Spitfire and Viper2.2.1.1 Packaging box Part DescriptionQuantity 2.2.1.2 Winder kitPart Description 2.2.2 For ValueJet 1604 series 2.2.2.1 Packaging boxPart Description QuantityQuantity 2.2.2.2 Winder kitPart Description 3 INSTALLING THE UNIT 3.1 GENERAL SEQUENCEINSTALL THE TENSIONING BARS ADJUST THE WEIGHT SUPPORTS UNDER THE ROLL UNIT BARS3.2 INSTALL ALL PARTS 3.2.1 Mounting the roll unit barsDescription Quantity neededNo. Description DescriptionIF … THEN …3.2.2 Mounting the brackets for the tensioning bars 3.2.2.1 On a Spitfire, Rockhopper 3 and ViperNo Description Description3.2.2.2 On a ValueJet Parts and Tools neededDescription Quantity3.2.3 Installing the tensioning bars ProcedureUse care when lifting the tensioning bars to avoid bending the bars Parts and Tools neededInstall the remaining screws on the left bracket. Tighten all screws 3.2.4 Mounting the PCB Box ProcedureParts and Tools needed Description3.2.5 Connecting the cables Nr Description3.3 CALIBRATING THE UW/W 3.3.1 Calibrating the rear tensioning system3.3.1.1 Checking the calibration Included in kitStep 4 Check if the edges of the loop are aligned on each other No DescriptionNo Description PART 2 DRAWING THE CONTROL LINESStep 4 Carefully pull the strip to create some tension No Description 3.3.1.2 Adjusting the tensioning systemsNo Description THEN turn the adjustment screws as follows Make sure to turn both adjustment screws an equal amount of turnsTool Hexagon wrench 3 mm IF Line 2 lays…3.3.2 Calibrating the front and rear roll unit bars 3.3.2.1 Introduction3.3.2.2 Checking the calibration of the roll units FRONT VIEWNo Description 1 Synthetic paper strip 2 Loop 3 Core 4 Pressure rollersStep 2 Draw a line. See image below No Description1 Synthetic paper strip 2 Loop 3 Core 4 Pressure rollers PART 2 DRAWING THE CONTROL LINESStep 5 Pull the strip so there is an equal tension 3.3.2.3 Adjusting the roll units No DescriptionNo Description 1 Spacer 2 Printer’s stand 3 Roll unit bar3.3.3 Adjusting the weight supports under the UW/W 3.3.3.1 Location of the weight supports on a 65” printer3.3.3.2 Location of the weight supports on a 90” printer Hexagon wrench 3 mm1 Hexagon wrench 6 mm 2 Turning direction to lower the support 3.3.3.3 Adjusting the weight supportsNo Description This page is intentionally left blank 3-24 4.1 TURNING THE POWER ON / OFF 4 OPERATING THE SYSTEM4.2 LOADING ROLL MEDIA MetricalMaximum loading capacity Maximum media widthOutside printable Inside PrintableHINT

3.2.3Installing the tensioning bars

RH3 & SPFR

ValueJet 1604

Step 1 :

front

rear

Use care when lifting the tensioning bars to avoid bending the bars.