Manuals / Xerox / Computer Equipment / Printer

Xerox 83xx, 82xx manual Adjusting the weight supports, No Description

Models: 82xx 83xx

1 44

Download 44 pages 1.37 Kb

Page 37

Image 37

3.3.3.3Adjusting the weight supports

Caution

•Don’t turn the weight supports with force when they reach the floor!

Instructions

Lower the weight supports of the UW/W 100 till they reach the floor. A hexagon wrench 6 mm can be used as indicated below.

No Description

1Hexagon wrench 6 mm

2Turning direction to lower the support

3-23

Page 37

Image 37

Xerox 83xx Adjusting the weight supports, No Description, Hexagon wrench 6 mm 2 Turning direction to lower the support

Contents

Unwinder / Winder User GuideXerox 82xx/83xx Wide Format Printer August800 Phillips Road, Bldg. 0218-01A Webster, New York USA Prepared by Xerox Corporation Global Knowledge and Language Services2007 by Xerox Corporation. All rights reserved trademarks are also acknowledged3-159H TABLE OF CONTENTS4-18 H This page is intentionally left blank 1.2 IMPORTANT SAFETY INSTRUCTIONS 1 SAFETY INSTRUCTIONSSafety terms 1.1 INTRODUCTIONFoot switch label 1.3 OPERATION LABELSFront tensioning label PCB box labelDisposal of your old product 1.4 WEEE REGULATIONSWEEE regulations Environmental informationThis page is intentionally left blank 2.1 PART NAMES AND FUNCTIONS 2 PRODUCT OVERVIEW2.1.1 Front / Winder 2.1.2 Rear / UnwinderName 2.1.3 Operation PanelFunction 2.2.1 For Rockhopper 3, Spitfire and Viper 2.2 VERIFYING THE PACKAGED ITEMS2.2.1.1 Packaging box Part DescriptionPart Description 2.2.1.2 Winder kitQuantity 2.2.2.1 Packaging box 2.2.2 For ValueJet 1604 seriesPart Description QuantityPart Description 2.2.2.2 Winder kitQuantity 3.1 GENERAL SEQUENCE 3 INSTALLING THE UNITINSTALL THE TENSIONING BARS ADJUST THE WEIGHT SUPPORTS UNDER THE ROLL UNIT BARS3.2.1 Mounting the roll unit bars 3.2 INSTALL ALL PARTSDescription Quantity neededDescription No. DescriptionIF … THEN …3.2.2.1 On a Spitfire, Rockhopper 3 and Viper 3.2.2 Mounting the brackets for the tensioning barsNo Description DescriptionParts and Tools needed 3.2.2.2 On a ValueJetDescription QuantityProcedure 3.2.3 Installing the tensioning barsUse care when lifting the tensioning bars to avoid bending the bars Parts and Tools neededInstall the remaining screws on the left bracket. Tighten all screws Procedure 3.2.4 Mounting the PCB BoxParts and Tools needed DescriptionNr Description 3.2.5 Connecting the cables3.3.1 Calibrating the rear tensioning system 3.3 CALIBRATING THE UW/W3.3.1.1 Checking the calibration Included in kitNo Description Step 4 Check if the edges of the loop are aligned on each otherPART 2 DRAWING THE CONTROL LINES No DescriptionStep 4 Carefully pull the strip to create some tension No Description 3.3.1.2 Adjusting the tensioning systemsNo Description Make sure to turn both adjustment screws an equal amount of turns THEN turn the adjustment screws as followsTool Hexagon wrench 3 mm IF Line 2 lays…3.3.2.1 Introduction 3.3.2 Calibrating the front and rear roll unit bars3.3.2.2 Checking the calibration of the roll units FRONT VIEW1 Synthetic paper strip 2 Loop 3 Core 4 Pressure rollers No DescriptionNo Description Step 2 Draw a line. See image below1 Synthetic paper strip 2 Loop 3 Core 4 Pressure rollers PART 2 DRAWING THE CONTROL LINESStep 5 Pull the strip so there is an equal tension No Description 3.3.2.3 Adjusting the roll units1 Spacer 2 Printer’s stand 3 Roll unit bar No Description3.3.3.1 Location of the weight supports on a 65” printer 3.3.3 Adjusting the weight supports under the UW/W3.3.3.2 Location of the weight supports on a 90” printer Hexagon wrench 3 mmNo Description 3.3.3.3 Adjusting the weight supports1 Hexagon wrench 6 mm 2 Turning direction to lower the support This page is intentionally left blank 3-24 4 OPERATING THE SYSTEM 4.1 TURNING THE POWER ON / OFFMetrical 4.2 LOADING ROLL MEDIAMaximum loading capacity Maximum media widthInside Printable Outside printableHINT