Manuals / Xerox / Computer Equipment / Printer

Xerox 83xx, 82xx manual Operating The System, Turning The Power On / Off

Models: 82xx 83xx

1 44

Download 44 pages 1.37 Kb

Page 39

Image 39

4 OPERATING THE SYSTEM

4.1 TURNING THE POWER ON / OFF

The switch in located on the power supply box.

Its status is marked with “O” and “I”.

“I”	Switched ON	Power LED on control panel of winding system will light up
“O”	Switched OFF	Power LED on control panel of winding system will not be lid.

4-1

Page 39

Image 39

Xerox 83xx, 82xx manual Operating The System, Turning The Power On / Off

Contents

August User GuideUnwinder / Winder Xerox 82xx/83xx Wide Format Printertrademarks are also acknowledged Prepared by Xerox Corporation Global Knowledge and Language Services800 Phillips Road, Bldg. 0218-01A Webster, New York USA 2007 by Xerox Corporation. All rights reservedTABLE OF CONTENTS 3-159H4-18 H This page is intentionally left blank 1.1 INTRODUCTION 1 SAFETY INSTRUCTIONS1.2 IMPORTANT SAFETY INSTRUCTIONS Safety termsPCB box label 1.3 OPERATION LABELSFoot switch label Front tensioning labelEnvironmental information 1.4 WEEE REGULATIONSDisposal of your old product WEEE regulationsThis page is intentionally left blank 2.1.2 Rear / Unwinder 2 PRODUCT OVERVIEW2.1 PART NAMES AND FUNCTIONS 2.1.1 Front / Winder2.1.3 Operation Panel NameFunction Part Description 2.2 VERIFYING THE PACKAGED ITEMS2.2.1 For Rockhopper 3, Spitfire and Viper 2.2.1.1 Packaging box2.2.1.2 Winder kit Part DescriptionQuantity Quantity 2.2.2 For ValueJet 1604 series2.2.2.1 Packaging box Part Description2.2.2.2 Winder kit Part DescriptionQuantity ADJUST THE WEIGHT SUPPORTS UNDER THE ROLL UNIT BARS 3 INSTALLING THE UNIT3.1 GENERAL SEQUENCE INSTALL THE TENSIONING BARSQuantity needed 3.2 INSTALL ALL PARTS3.2.1 Mounting the roll unit bars DescriptionTHEN … No. DescriptionDescription IF …Description 3.2.2 Mounting the brackets for the tensioning bars3.2.2.1 On a Spitfire, Rockhopper 3 and Viper No DescriptionQuantity 3.2.2.2 On a ValueJetParts and Tools needed DescriptionParts and Tools needed 3.2.3 Installing the tensioning barsProcedure Use care when lifting the tensioning bars to avoid bending the barsInstall the remaining screws on the left bracket. Tighten all screws Description 3.2.4 Mounting the PCB BoxProcedure Parts and Tools neededNr Description 3.2.5 Connecting the cablesIncluded in kit 3.3 CALIBRATING THE UW/W3.3.1 Calibrating the rear tensioning system 3.3.1.1 Checking the calibrationNo Description Step 4 Check if the edges of the loop are aligned on each otherPART 2 DRAWING THE CONTROL LINES No DescriptionStep 4 Carefully pull the strip to create some tension 3.3.1.2 Adjusting the tensioning systems No DescriptionNo Description IF Line 2 lays… THEN turn the adjustment screws as followsMake sure to turn both adjustment screws an equal amount of turns Tool Hexagon wrench 3 mmFRONT VIEW 3.3.2 Calibrating the front and rear roll unit bars3.3.2.1 Introduction 3.3.2.2 Checking the calibration of the roll units1 Synthetic paper strip 2 Loop 3 Core 4 Pressure rollers No DescriptionPART 2 DRAWING THE CONTROL LINES Step 2 Draw a line. See image belowNo Description 1 Synthetic paper strip 2 Loop 3 Core 4 Pressure rollersStep 5 Pull the strip so there is an equal tension No Description 3.3.2.3 Adjusting the roll units1 Spacer 2 Printer’s stand 3 Roll unit bar No DescriptionHexagon wrench 3 mm 3.3.3 Adjusting the weight supports under the UW/W3.3.3.1 Location of the weight supports on a 65” printer 3.3.3.2 Location of the weight supports on a 90” printer3.3.3.3 Adjusting the weight supports No Description1 Hexagon wrench 6 mm 2 Turning direction to lower the support This page is intentionally left blank 3-24 4 OPERATING THE SYSTEM 4.1 TURNING THE POWER ON / OFFMaximum media width 4.2 LOADING ROLL MEDIAMetrical Maximum loading capacityInside Printable Outside printableHINT