Manuals / Xerox / Computer Equipment / Printer

Xerox 82xx, 83xx manual Operation Labels, Foot switch label, Front tensioning label, PCB box label

Models: 82xx 83xx

1 44

Download 44 pages 1.37 Kb

Page 6

Image 6

1.3 OPERATION LABELS

The operation labels mentioned below are attached to areas to which attention should be paid.

Notes

•Make sure that all labels can be recognized. If text or illustrations are invisible, clean the label.

•When cleaning labels, use a cloth with water or neutral detergent. Do not use a solvent or gasoline.

•If an operation label has been damaged, lost or cannot be recognized, replace the label.

Foot switch label

Roll unit handle label

Front tensioning label

Rear tensioning label

PCB box label

1-2

Page 6

Image 6

Xerox 82xx, 83xx manual Operation Labels, Foot switch label, Front tensioning label, PCB box label

Contents

Xerox 82xx/83xx Wide Format Printer User GuideUnwinder / Winder August2007 by Xerox Corporation. All rights reserved Prepared by Xerox Corporation Global Knowledge and Language Services800 Phillips Road, Bldg. 0218-01A Webster, New York USA trademarks are also acknowledgedTABLE OF CONTENTS 3-159H4-18 H This page is intentionally left blank Safety terms 1 SAFETY INSTRUCTIONS1.2 IMPORTANT SAFETY INSTRUCTIONS 1.1 INTRODUCTIONFront tensioning label 1.3 OPERATION LABELSFoot switch label PCB box labelWEEE regulations 1.4 WEEE REGULATIONSDisposal of your old product Environmental informationThis page is intentionally left blank 2.1.1 Front / Winder 2 PRODUCT OVERVIEW2.1 PART NAMES AND FUNCTIONS 2.1.2 Rear / Unwinder2.1.3 Operation Panel NameFunction 2.2.1.1 Packaging box 2.2 VERIFYING THE PACKAGED ITEMS2.2.1 For Rockhopper 3, Spitfire and Viper Part Description2.2.1.2 Winder kit Part DescriptionQuantity Part Description 2.2.2 For ValueJet 1604 series2.2.2.1 Packaging box Quantity2.2.2.2 Winder kit Part DescriptionQuantity INSTALL THE TENSIONING BARS 3 INSTALLING THE UNIT3.1 GENERAL SEQUENCE ADJUST THE WEIGHT SUPPORTS UNDER THE ROLL UNIT BARSDescription 3.2 INSTALL ALL PARTS3.2.1 Mounting the roll unit bars Quantity neededIF … No. DescriptionDescription THEN …No Description 3.2.2 Mounting the brackets for the tensioning bars3.2.2.1 On a Spitfire, Rockhopper 3 and Viper DescriptionDescription 3.2.2.2 On a ValueJetParts and Tools needed QuantityUse care when lifting the tensioning bars to avoid bending the bars 3.2.3 Installing the tensioning barsProcedure Parts and Tools neededInstall the remaining screws on the left bracket. Tighten all screws Parts and Tools needed 3.2.4 Mounting the PCB BoxProcedure Description3.2.5 Connecting the cables Nr Description3.3.1.1 Checking the calibration 3.3 CALIBRATING THE UW/W3.3.1 Calibrating the rear tensioning system Included in kitStep 4 Check if the edges of the loop are aligned on each other No DescriptionNo Description PART 2 DRAWING THE CONTROL LINESStep 4 Carefully pull the strip to create some tension 3.3.1.2 Adjusting the tensioning systems No DescriptionNo Description Tool Hexagon wrench 3 mm THEN turn the adjustment screws as followsMake sure to turn both adjustment screws an equal amount of turns IF Line 2 lays…3.3.2.2 Checking the calibration of the roll units 3.3.2 Calibrating the front and rear roll unit bars3.3.2.1 Introduction FRONT VIEWNo Description 1 Synthetic paper strip 2 Loop 3 Core 4 Pressure rollers1 Synthetic paper strip 2 Loop 3 Core 4 Pressure rollers Step 2 Draw a line. See image belowNo Description PART 2 DRAWING THE CONTROL LINESStep 5 Pull the strip so there is an equal tension 3.3.2.3 Adjusting the roll units No DescriptionNo Description 1 Spacer 2 Printer’s stand 3 Roll unit bar3.3.3.2 Location of the weight supports on a 90” printer 3.3.3 Adjusting the weight supports under the UW/W3.3.3.1 Location of the weight supports on a 65” printer Hexagon wrench 3 mm3.3.3.3 Adjusting the weight supports No Description1 Hexagon wrench 6 mm 2 Turning direction to lower the support This page is intentionally left blank 3-24 4.1 TURNING THE POWER ON / OFF 4 OPERATING THE SYSTEMMaximum loading capacity 4.2 LOADING ROLL MEDIAMetrical Maximum media widthOutside printable Inside PrintableHINT