Manuals / Xerox / Computer Equipment / Printer

Xerox 83xx, 82xx manual Introduction, Important Safety Instructions, Safety terms, Details

Models: 82xx 83xx

1 44

Download 44 pages 1.37 Kb

Page 5

1 SAFETY INSTRUCTIONS

1 SAFETY INSTRUCTIONS

1.1 INTRODUCTION

Important

BE SURE TO READ THE TERMS IN THE NEXT CHAPTER THOROUGHLY BEFORE INSTALLING AND OPERATING THE SYSTEM FOR YOUR OWN SAFETY.

All safety related terms are bundled and categorized in three types.

Safety terms	Details
	Must be followed carefully to avoid death or serious bodily injury
Important
	Must be observed to avoid bodily injury (moderate or light) or damage to your equipment
Caution
	Contains important information and useful tips on the operation of your printer
Notes

1.2 IMPORTANT SAFETY INSTRUCTIONS

General safety instructions that must be observed to use the equipment safely are explained below.

¾Do not stand on or place heavy objects on the unit. Doing so may result in the unit tipping or falling over and causing injury.

¾Do not attempt to plug in electrical plugs with wet hands. Doing so may result in electrical shock.

¾Do not use thinner, benzene, alcohol or other active agents. Doing so may result in damage or paint peeling from the casing.

¾Be careful not to spill water inside the winder. Doing so may result in a short-circuit.

¾Never open the covers fixed with screws. Doing so may result in electrical shock or a malfunctioning in the unit.

¾When setting roll media, place it on top of a desk or other flat surface

1-1

Image 5

Xerox 83xx, 82xx manual Introduction, Important Safety Instructions, Safety terms, Details

Contents

Unwinder / Winder User GuideXerox 82xx/83xx Wide Format Printer August800 Phillips Road, Bldg. 0218-01A Webster, New York USA Prepared by Xerox Corporation Global Knowledge and Language Services2007 by Xerox Corporation. All rights reserved trademarks are also acknowledged4-18 H TABLE OF CONTENTS3-159H This page is intentionally left blank 1.2 IMPORTANT SAFETY INSTRUCTIONS 1 SAFETY INSTRUCTIONSSafety terms 1.1 INTRODUCTIONFoot switch label 1.3 OPERATION LABELSFront tensioning label PCB box labelDisposal of your old product 1.4 WEEE REGULATIONSWEEE regulations Environmental informationThis page is intentionally left blank 2.1 PART NAMES AND FUNCTIONS 2 PRODUCT OVERVIEW2.1.1 Front / Winder 2.1.2 Rear / UnwinderFunction 2.1.3 Operation PanelName 2.2.1 For Rockhopper 3, Spitfire and Viper 2.2 VERIFYING THE PACKAGED ITEMS2.2.1.1 Packaging box Part DescriptionQuantity 2.2.1.2 Winder kitPart Description 2.2.2.1 Packaging box 2.2.2 For ValueJet 1604 seriesPart Description QuantityQuantity 2.2.2.2 Winder kitPart Description 3.1 GENERAL SEQUENCE 3 INSTALLING THE UNITINSTALL THE TENSIONING BARS ADJUST THE WEIGHT SUPPORTS UNDER THE ROLL UNIT BARS3.2.1 Mounting the roll unit bars 3.2 INSTALL ALL PARTSDescription Quantity neededDescription No. DescriptionIF … THEN …3.2.2.1 On a Spitfire, Rockhopper 3 and Viper 3.2.2 Mounting the brackets for the tensioning barsNo Description DescriptionParts and Tools needed 3.2.2.2 On a ValueJetDescription QuantityProcedure 3.2.3 Installing the tensioning barsUse care when lifting the tensioning bars to avoid bending the bars Parts and Tools neededInstall the remaining screws on the left bracket. Tighten all screws Procedure 3.2.4 Mounting the PCB BoxParts and Tools needed DescriptionNr Description 3.2.5 Connecting the cables3.3.1 Calibrating the rear tensioning system 3.3 CALIBRATING THE UW/W3.3.1.1 Checking the calibration Included in kitNo Description Step 4 Check if the edges of the loop are aligned on each otherPART 2 DRAWING THE CONTROL LINES No DescriptionStep 4 Carefully pull the strip to create some tension No Description 3.3.1.2 Adjusting the tensioning systemsNo Description Make sure to turn both adjustment screws an equal amount of turns THEN turn the adjustment screws as followsTool Hexagon wrench 3 mm IF Line 2 lays…3.3.2.1 Introduction 3.3.2 Calibrating the front and rear roll unit bars3.3.2.2 Checking the calibration of the roll units FRONT VIEW1 Synthetic paper strip 2 Loop 3 Core 4 Pressure rollers No DescriptionNo Description Step 2 Draw a line. See image below1 Synthetic paper strip 2 Loop 3 Core 4 Pressure rollers PART 2 DRAWING THE CONTROL LINESStep 5 Pull the strip so there is an equal tension No Description 3.3.2.3 Adjusting the roll units1 Spacer 2 Printer’s stand 3 Roll unit bar No Description3.3.3.1 Location of the weight supports on a 65” printer 3.3.3 Adjusting the weight supports under the UW/W3.3.3.2 Location of the weight supports on a 90” printer Hexagon wrench 3 mm1 Hexagon wrench 6 mm 2 Turning direction to lower the support 3.3.3.3 Adjusting the weight supportsNo Description This page is intentionally left blank 3-24 4 OPERATING THE SYSTEM 4.1 TURNING THE POWER ON / OFFMetrical 4.2 LOADING ROLL MEDIAMaximum loading capacity Maximum media widthInside Printable Outside printableHINT