Manuals / Yamaha / Computer Equipment / Projector

Yamaha DPX-1300 G manual Connecting to computer devices, RGB Digital DVI connector

Models: DPX-1300 G

1 67

Page 18

Connecting to computer devices

You can use the following three methods to connect to computer devices. Be sure to use cables with jacks that match the connectors and jacks you wish to use. The HDMI terminal does not support PC signals.

Input

Signal type

Connector type

INPUT A

RGB (Analog)

BNC jack x 5

INPUT B

RGB (Analog)

D-sub 15 pin

DVI

RGB (Digital)

DVI connector

						OUT		IN
DVI	HDMI						REMOTE	RS-232C	TRIGGER OUT
INPUT B				INPUT A
RGB/YPBPR/YCBCR	D4 VIDEO	G/Y	B/PB/CB	R/PR/CR	HD/SYNC	VD		S VIDEO	VIDEO

D-Sub monitorBNC monitor cable cable

Monitor output terminal

DVI cable

Computer devices

Page 18

Image 18

Yamaha DPX-1300 G manual Connecting to computer devices, RGB Digital DVI connector

Contents

DPX-1300 Others InstallationOperation For U.K. customersTable of contents Inappropriate places for installation Accessory checkFeatures Features EnglishMain unit Front panel and controls Main unit Rear panel / Connections Controls and functionsRemote control functions Remote control code switch Remote control EnglishLight switch Remote control cable jackLoading the batteries into the remote control Using the remote control with a wired connectionLimits for using the remote control Distance to sensor Angle to sensorUse within a left/right arc of 30 degrees If you have not installed the main unit or screen PreparationTurn the power on and selecting an image for projection PrepararionSetting up the DPX-1300 Mounting the projector on a tableMounting the projector on the ceiling When using a 43 screen InstallationWhen using a 169 screen Projection distanceUsing V.POS vertical position to adjust image position Keystone adjustmentUsing Zoom to adjust image position Using the adjusters to adjust image positionConnecting to AV components ConnectionConnecting to computer devices RGB Digital DVI connectorProjection English Checking installation and connectionsPre-operation check Projection preparations completeTurning the projector power on Turning the power onPress the STANDBY/ON button Button on the remote control Placing the DPX-1300 in standby mode Lamp may blink when half lit. This is not a defectPress the STANDBY/ON button Selecting an input signal Selecting using the Input buttonProjection image signal Using the Input button to select a signal ProjectionPress the + button to open the submenu Selecting a display aspect for a projection image Press the Aspect buttonRemote cotrol Display aspect types Input signal type Input image Display aspect Projected image Representative examplesPattern button Adjusting the imageAdjusting the vertical position V.POS button Crosshatch pattern Grayscale pattern Color bar patternAdjusting the size of an image Zoom button Menu configurations Menu screenMenu items Menu item listSubmenu Items Lower level menu itemsMenu group items and functions Menu Adjusts the analog input signal gain and offset settings Level AdjustmentAdjusts the iris Optical White PeakingSignal Menu EnglishOvershoot Supp. Range Signal LevelSignal Status Overshoot Supp. LevelInitial Setup Trigger Out Menu ColorMessage Baud RateMenu operations Reset button Remote control onlyRemote Control Operation button functionsMenu screen Menu operations 1 with no submenuPress the Menu button to open Press the + or button to select a menu groupRemote Control Main Unit Menu Button Press the + or button to select a suitable settingSetting method depends on the item selected Remote Control Main UnitPress the + button to move to the submenu Press the h or g button to adjust item settingsMenu operations 2 with submenus Appears to the right of items that contain a submenuSpecial operations See page 32 for datails about each color itemExample Using the color temperature fixed mode Example Color temperature fixed modeName of the selected item appears here Resetting the selected settings Resetting all the settingsChanging the position of the menu screen Resetting the lamp running time Subtitle ZoomChanging the Gamma Press the buttonInline menu composition Adjusting image quality using the inline menuExample Using the inline menu Inline menu item listUsing the remote control Memory configurationsSaving memory settings Using the menuBottom of the screen Memory function EnglishPress the g button to select Memory number status from Press the h or g button to select a memory numberDeactivating Memory Lock Setting Memory LockMemory lock Select the memory number youCopy source Memory copyRecall the memory number to be Press the g button to selectPress the + button to display the confirmation screen Press ButtonResetting to the default settings in the memory menu Initialization of the currently selected memoryInitialization of all the memories Glossary ReferenceCompatible signal types Signal type Active Component type Pixels Lines KHz Reference EnglishMaintenance Regular careReplacing the filter Replacing the lamp Loosen the lamp cover screwsLamp cover screws Troubleshooting To protect the lamp, you cannot turn onTroubleshooting Message display Message ConditionLED indicator meanings LED indicator State MeaningControls SpecificationsOptical GeneralDimensional drawing 119.1