Manuals / Yamaha / Computer Equipment / Projector

Yamaha DPX-1300 G manual Turning the projector power on, Turning the power on

Models: DPX-1300 G

1 67

Download 67 pages 31.66 Kb

Page 20

Turning the projector power on

◆Turning the power on

Always remove the lens cap before operating the main unit.

	STANDBY/ON
	STANDBY/ON
	indicator
ESCAPE	MENU
PATTERN	SETTING
ASPECT	INPUT
	LAMP COVER TEMP FAN

1.Insert the supplied power cable firmly into the AC inlet at the rear of the main unit, then insert the plug into an AC outlet.

The STANDBY/ON indicator lights red.

		AC inlet
		button STANDBY/ON button
AUTO
			STANDBY/ON
V. POS	ZOOM	FOCUS
IRIS	SETTING	PATT
		ESCAPE	MENU
ESCAPE		MENU
		PATTERN	SETTING
		ASPECT	INPUT
ASPECT		INPUT	LAMP COVER TEMP FAN
ASPECT		INPUT
Remote Control			Main unit

2.Press the STANDBY/ON button

(the button on the remote control).

The indicator blinks green and the lamp lights up in preparation for projection. After approximately 35 seconds, the indicator changes from blinking to steady green, indicating that the unit is ready to project.

Warning

•Do not remove the power cable while the STANDBY/ON indicator is blinking green or lit steady green. This could damage the lamp or reduce lamp life.

18

Image 20

Yamaha DPX-1300 G manual Turning the projector power on, Turning the power on

Contents

DPX-1300 Installation OperationOthers For U.K. customersTable of contents Inappropriate places for installation Accessory checkFeatures Features EnglishMain unit Front panel and controls Main unit Rear panel / Connections Controls and functionsRemote control functions Remote control English Light switchRemote control code switch Remote control cable jackLoading the batteries into the remote control Using the remote control with a wired connectionUse within a left/right arc of 30 degrees Limits for using the remote controlDistance to sensor Angle to sensor If you have not installed the main unit or screen PreparationTurn the power on and selecting an image for projection PrepararionMounting the projector on the ceiling Setting up the DPX-1300Mounting the projector on a table Installation When using a 169 screenWhen using a 43 screen Projection distanceKeystone adjustment Using Zoom to adjust image positionUsing V.POS vertical position to adjust image position Using the adjusters to adjust image positionConnecting to AV components ConnectionConnecting to computer devices RGB Digital DVI connectorChecking installation and connections Pre-operation checkProjection English Projection preparations completePress the STANDBY/ON button Button on the remote control Turning the projector power onTurning the power on Press the STANDBY/ON button Placing the DPX-1300 in standby modeLamp may blink when half lit. This is not a defect Projection image signal Selecting an input signalSelecting using the Input button Press the + button to open the submenu Using the Input button to select a signalProjection Remote cotrol Selecting a display aspect for a projection imagePress the Aspect button Display aspect types Input signal type Input image Display aspect Projected image Representative examplesAdjusting the image Adjusting the vertical position V.POS buttonPattern button Crosshatch pattern Grayscale pattern Color bar patternAdjusting the size of an image Zoom button Menu configurations Menu screenMenu items Menu item listSubmenu Items Lower level menu itemsMenu group items and functions Menu Level Adjustment Adjusts the iris OpticalAdjusts the analog input signal gain and offset settings White PeakingSignal Menu EnglishSignal Level Signal StatusOvershoot Supp. Range Overshoot Supp. LevelInitial Setup Menu Color MessageTrigger Out Baud RateReset button Remote control only Remote ControlMenu operations Operation button functionsMenu operations 1 with no submenu Press the Menu button to openMenu screen Press the + or button to select a menu groupPress the + or button to select a suitable setting Setting method depends on the item selectedRemote Control Main Unit Menu Button Remote Control Main UnitPress the h or g button to adjust item settings Menu operations 2 with submenusPress the + button to move to the submenu Appears to the right of items that contain a submenuSpecial operations See page 32 for datails about each color itemName of the selected item appears here Example Using the color temperature fixed modeExample Color temperature fixed mode Changing the position of the menu screen Resetting the selected settingsResetting all the settings Resetting the lamp running time Subtitle ZoomChanging the Gamma Press the buttonAdjusting image quality using the inline menu Example Using the inline menuInline menu composition Inline menu item listMemory configurations Saving memory settingsUsing the remote control Using the menuMemory function English Press the g button to select Memory number status fromBottom of the screen Press the h or g button to select a memory numberSetting Memory Lock Memory lockDeactivating Memory Lock Select the memory number youMemory copy Recall the memory number to beCopy source Press the g button to selectPress the + button to display the confirmation screen Press ButtonResetting to the default settings in the memory menu Initialization of the currently selected memoryInitialization of all the memories Glossary ReferenceCompatible signal types Signal type Active Component type Pixels Lines KHz Reference EnglishReplacing the filter MaintenanceRegular care Lamp cover screws Replacing the lampLoosen the lamp cover screws Troubleshooting To protect the lamp, you cannot turn onTroubleshooting Message display Message ConditionLED indicator meanings LED indicator State MeaningSpecifications OpticalControls GeneralDimensional drawing 119.1