Manuals / Brands / Home Audio / Stereo Amplifier / Yamaha / Home Audio / Stereo Amplifier

Yamaha DSP-A2 PAL/NTSC switch, PAL/NTSC switch (China and General models only)

1 78

Download 78 pages, 1.3 Mb

PREPARATION

For connecting with a TV monitor that uses a 21 pin connector for input (Europe and U.K. models only)

Make a connection as figured below with a commercially available scart-plug connector cable.

(Europe model)

		MAIN	IN	IN
	IN		VCR 2	VCR 2
	IN
	(PLAY)	SURROUND	OUT	OUT	COUPLER
	TAPE/MD	SURROUND	OUT	OUT	COUPLER
	TAPE/MD				MAIN
					MAIN
	OUT		2		PRE	MAIN
	(REC)		2		OUT	IN
			TUNER
	DVD/LD	SUB WOOFER	CENTER	S VIDEO
		SUB WOOFER	CENTER

		EXTERNAL DECODER INPUT		MONITOR
		EXTERNAL DECODER INPUT		OUT
	TV/DBS			OUT
	TV/DBS
				VIDEO
	DIGITAL SIGNAL

No connection

VIDEO

AUDIO L

AUDIO R

TV monitor

Scart-plug connector cable

PAL/NTSC switch (China and General models only)

This unit is designed for use with the NTSC and PAL television formats. Set this switch to the position for the format your TV monitor employs.

IN

VCR 1

OUT

PAL NTSC

CAUTION

IN

VCR 2

PAL/NTSC switch

PAL: Set to this position if your TV monitor employs the PAL format.

*Outputs signals in the PAL format no matter which format (PAL or NTSC) of video signal is sent from an external video unit to this unit.

NTSC: Set to this position if your TV monitor employs the NTSC format.

*Outputs signals in the NTSC format no matter which format (PAL or NTSC) of video signal is sent from an external video unit to this unit.

Note

Be sure to input a video signal which employs the same format that your TV monitor employs, otherwise a picture will not be played back normally.

16

Contents

NATURAL SOUND AV AMPLIFIER AMPLIFICATEUR AUDIO-VIDEO OWNER’S MANUAL MODE D’EMPLOI BEDIENUNGSANLEITUNG Page CONTENTS English Selecting the output modes Recording a source to tape (or MD) or dubbing Using digital sound field processor (DSP) CAUTION : Read this before operating your unit INTRODUCTION Features Power, 0.02% THD, 20–20,000Hz What’s DSP Dolby Digital DTS Digital Surround Dolby Pro Logic + 2 Digital Sound Fields Dolby Digital or DTS + 3 Digital Sound Fields GETTING STARTED Getting started Installing batteries in the remote controller Notes about the remote controller Battery replacement Remote controller operation range Controls and their functions Page Display panel PREPARATION Speaker setup mRecommended speaker system configurations 4 Speaker System 5 Speaker System 6 Speaker System 7 Speaker System Connections m Basic connections of video units VIDEO AUX terminals (on the front panel) PAL/NTSC switch (China and General models only) PAL/NTSC switch mConnecting to digital (OPTICAL and COAXIAL) terminals mConnecting to DOLBY DIGITAL RF output of the DVD/LD/CD combi-player mConnecting to S VIDEO terminals Notes about the Video superimpose mConnecting an external decoder of a future format to this unit How to Connect: Note on main speaker connections: Note on a subwoofer connection: mIMPEDANCE SELECTOR switch IMPEDANCE SELECTOR 1 MAIN PRE OUT/MAIN IN terminals 3CENTER terminal 4FRONT terminals 5REAR (SURROUND) terminals 2SUBWOOFER terminal AC OUTLET(S) Voltage Selector (China and General models only) On screen display Selecting the output modes (“SET MENU” mode) 1C. MAIN SP 1E. SYS. SETUP 1D. LFE/BASS OUT 1F. MAIN LEVEL mChanging selections 2, 3 Speaker balance adjustment Page 11 BASIC OPERATION Playing a source Page When you finish using this unit mSwitching the input mode vFor CD, TAPE/MD and TV/DBS sources: AUTO: DTS: ANALOG Page Recording a source to tape (or MD) or dubbing from tape (or MD) to tape (or MD) mRecording the playing source to tape (or MD) 3, 5 Page Page Page Page Page Page Page Page Page Page Page ADVANCED FEATURES “SET MENU” mode 1.SPEAKER SET (Selecting the output modes suitable for your speaker system) 2. DLBY DGTL (DOLBY DIGITAL) SET 2B. D-RANGE(Adjusting dynamic range) 4. CENTER DELAY [Adjusting the delay of center sounds (dialog etc.)] 5. PARAMETER INI (Initializing parameters on a DSP program) 6. MEMORY GUARD (Locking DSP parameters and other adjustments) 8. DIMMER (Changing brightness of the display panel) Creating your own sound fields mSelecting and editing program parameters 4, 5 P. ROOM SIZE (Presence Room Size) S. ROOM SIZE (Surround Room Size) P. INIT. DLY (Presence Initial Delay) S. INIT. DLY (Surround Initial Delay) LIVENESS (Presence Liveness) S. LIVENESS (Surround Liveness) ●REV. LEVEL (Reverberation Level) ●S. DELAY (Surround Delay) Setting the SLEEP timer REMOTE CONTROLLER Basic operation (Cover is open) Page Using the “learning-capable”keys (Cover is open) Keys which can have three functions (1, 2, 3, 4) Empty keys (1, 2) Using OPERATION CONTROL keys (Cover is closed) About the lighting of keys Macro operations (Cover is closed) Page Methods of learning and clearing functions mMaking a new macro mClearing learned functions To Clear a Learned Function To Clear All Learned Functions TROUBLESHOOTING Remote controller When playing back a source encoded with DTS: SPECIFICATIONS VIDEO SECTION GENERAL