Yamaha DSP-A2 CAUTION : Read this before operating your unit

CAUTION : Read this before operating your unit.

1.	To assure the finest performance, please read this manual
	carefully. Keep it in a safe place for future reference.
2.	Install this unit in a cool, dry, clean place – away from windows,
	heat sources, sources of excessive vibration, dust, moisture and
	cold. Avoid sources of humming (transformers, motors). To
	prevent fire or electrical shock, do not expose the unit to rain or
	water.
3.	Never remove the unit cover. Contact your dealer if an object falls
	inside the unit.
4.	Do not use force on switches, controls or connection wires. When
	moving the unit, first disconnect the power plug and the wires
	connected to other equipment. Never pull on the wires
	themselves.
5.	The openings on the unit cover assure proper ventilation of the
	unit. If these openings are obstructed, the temperature inside the
	unit will rise rapidly. Therefore, avoid placing objects against these
	openings, and install the unit in a well-ventilated area to prevent
	fire and damage.
	<Europe and U.K. models>

This unit is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this unit itself is turned off. This state is called the standby mode.

In this mode, this unit is designed to consume a small amount of power.

WARNING

Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise this unit may be damaged.

IF THIS UNIT FAILS TO TURN ON WHEN THE STANDBY/ON SWITCH IS PRESSED:

The IMPEDANCE SELECTOR switch may not be set to either end. If so, set the switch to either end when this unit is in the standby mode.

(Europe model)

	Be sure to allow a space of at least 10 cm behind, 20 cm on the
	both sides and 30 cm above the top panel of the unit to prevent
	fire and damage.
6.	The voltage used must be the same as that specified on this unit.
	Using this unit with a higher voltage than specified is dangerous
	and may result in fire or other accidents. YAMAHA will not be held
	responsible for any damage resulting from use of this unit with a
	voltage other than specified.
7.	Digital signals generated by this unit may interfere with other

KERS

REAR

(SURROUND)

OR CORRECT SETTING.

AIN A

B

AC OUTLETS

SWITCHED

I00W MAX.

TOTAL

CENTER	:	4ΩMIN. / SPEAKER
FRONT	:	6ΩMIN. / SPEAKER
REAR	:	6ΩMIN. / SPEAKER
MAIN A OR B: 4ΩMIN. / SPEAKER
A	B :	8ΩMIN. / SPEAKER
CENTER	:	8ΩMIN. / SPEAKER
FRONT	:	8ΩMIN. / SPEAKER
REAR	:	8ΩMIN. / SPEAKER
MAIN A OR B:		8ΩMIN. / SPEAKER
A	B :	I6ΩMIN. / SPEAKER

equipment such as tuners, receivers or TVs. Move this unit farther

away from such equipment if interference is observed.

8. Always set the VOLUME control to “–∞” before starting the audio

source play. Increase the volume gradually to an appropriate level

after playback has been started.

9. Do not attempt to clean the unit with chemical solvents; this might

damage the finish. Use a clean, dry cloth.

10. Be sure to read the “TROUBLESHOOTING” section regarding

common operating errors before concluding that the unit is faulty.

11. When not planning to use this unit for long periods of time,

disconnect the AC power plug from the wall outlet.

12. To prevent lightning damage, disconnect the AC power plug and

antenna cable when there is an electrical storm.

13. Grounding or polarization – Precautions should be taken so that

the grounding or polarization of an appliance is not defeated.

14. Do not connect an audio unit to the AC outlet on the rear panel if

the equipment requires more power than the outlet is rated to

provide.

15. Voltage Selector (China and General models only)

The voltage selector on the rear panel of this unit must be set

for your local main voltage BEFORE plugging into the AC

main supply.

Voltages are 110/120/220/240 V AC, 50/60 Hz.

IMPORTANT

Please record the serial number of your unit in the space below.

Model:

Serial No.:

The serial number is located on the rear of the unit.

Retain this Owner’s Manual in a safe place for future reference.

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.

SET BEFORE POWER ON

IMPEDANCE SELECTOR

IMPEDANCE

SELECTOR

For U.K. customers

If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below.

Note: The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet.

Special Instructions for U.K. Model

IMPORTANT

THE WIRES IN MAINS LEAD ARE COLOURED IN

ACCORDANCE WITH THE FOLLOWING CODE:

Blue: NEUTRAL

Brown: LIVE

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. Making sure that neither core is connected to the earth terminal of the three pin plug.

2