CONNECTIONS
IMPEDANCE SELECTOR Switch
WARNINGDo not change the IMPEDANCE SELECTOR switch setting while the power of this unit is on, otherwise the unit may be damaged.
If this unit fails to turn on when STANDBY/ON (or POWER) is pressed, the IMPEDANCE SELECTOR switch may not be fully slid to either position. If so, slide the switch to either position fully when this unit is in the standby mode.
Select the left or right position according to the impedance of the speakers in your system. Be sure to move this switch only when this unit is in the standby mode.
(General model)
VOLTAGE SELECTOR
AC OUTLETS
SWITCHED 100W MAX.
TOTAL
IMPEDANCE SELECTOR |
|
|
|
|
| ||||
| SET BEFORE POWER ON |
| MAIN A OR B: 8 | MIN. /SPEAKER | |||||
|
|
|
|
|
| A + B:16 MIN. /SPEAKER | |||
|
|
|
|
|
| CENTER | : 8 | MIN. /SPEAKER | |
|
|
|
|
|
| REAR | : 8 | MIN. /SPEAKER | |
|
|
|
|
|
|
|
|
|
|
|
| MAIN A OR B: 4 | MIN. /SPEAKER |
|
|
| |||
|
|
| A + B: 8 | MIN. /SPEAKER |
|
|
| ||
|
| CENTER | : 6 | MIN. /SPEAKER |
|
|
| ||
|
| REAR | : 6 | MIN. /SPEAKER |
|
|
| ||
|
|
|
|
|
|
|
|
|
|
VOLTAGE SELECTOR
IMPEDANCE SELECTOR
| Switch | Speaker | Impedance level | |
| position |
|
| |
|
|
| |
|
| If you use one set of main speakers, the impedance of | |
|
| each speaker must be 4 Ω or higher. | |
| Main |
| |
| Left | If you use two sets of main speakers, the impedance of | ||
| |||
| each speaker must be 8 Ω or higher. | ||
| Center | The impedance must be 6 Ω or higher. | |
|
|
| |
| Rear | The impedance of each speaker must be 6 Ω or higher. | |
|
|
| |
|
| If you use one set of main speakers, the impedance of | |
| Main | each speaker must be 8 Ω or higher. | |
|
| ||
| If you use two sets of main speakers, the impedance of | ||
|
| ||
| Right |
| each speaker must be 16 Ω or higher. | |
| Center | The impedance must be 8 Ω or higher. | |
|
|
| |
| Rear | The impedance of each speaker must be 8 Ω or higher. | |
|
|
|
PREPARATION
The VOLTAGE SELECTOR on the rear panel of this unit must be set for your local main voltage BEFORE plugging into the AC main supply. Voltages are 110/120/220/240 V AC, 50/60 Hz.
Connecting the Power Supply Cords
After completing all connections, connect the AC power cord to an AC power outlet. Disconnect the AC power cord if you will not use this unit for a long period of time.
(Europe model)
MAINS
AC OUTLETS
|
|
|
|
|
|
| SWITCHED |
|
|
|
| ||
IMPEDANCE |
|
|
|
| 100W MAX. TOTAL |
|
|
| |||||
|
|
|
|
|
|
|
|
|
| ||||
| SELECTOR |
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
| ||||
| SET BEFORE POWER ON |
| MAIN A OR B: 8 | MIN. /SPEAKER |
|
|
| ||||||
|
|
|
|
|
|
| A + B:16 MIN. /SPEAKER |
|
|
| |||
|
|
|
|
|
|
| CENTER | : 8 | MIN. /SPEAKER | To AC outlet | |||
|
|
|
|
|
|
| REAR | : 8 | MIN. /SPEAKER | ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| MAIN A OR B: 4 | MIN. /SPEAKER |
|
|
|
|
|
| ||||
|
|
|
| A + B: 8 MIN. /SPEAKER |
|
|
|
|
|
| |||
|
| CENTER | : 6 | MIN. /SPEAKER |
|
|
|
|
|
| |||
|
| REAR | : 6 | MIN. /SPEAKER |
|
|
|
|
|
| |||
| Europe, China and General models ............. | 2 OUTLETS |
U.K. model ..................................................... | 1 OUTLET |
Use these outlets to connect the power cords only from your audio/video components to this unit. The power to the AC OUTLET(S) is controlled by this unit’s STANDBY/ON (or POWER and STANDBY). These outlets will supply power to any connected component whenever this unit is turned on. The maximum power (total power consumption of components) that can be connected to the AC OUTLET(S) is 100 W.
English
SWITCHED
19