CAUTION: READ THIS BEFORE OPERATING YOUR SYSTEM.
1To assure the finest performance, please read this manual carefully. Keep it in a safe place for future reference.
2Do not install this equipment in a confined space, such as a book case or built in cabinet.
3Locate this system away from other electrical appliances, motors, or transformers to avoid humming sounds. To prevent fire or electrical shock, do not place this system where it may get exposed to dripping or splashing, and never put any objects filled with liquids, such as vases, on the top of the system.
4Do not expose this system to sudden temperature changes from cold to hot, and do not locate this system in a environment with high humidity (i.e. a room with a humidifier) to prevent condensation inside this system, which may cause an electrical shock, fire, damage to this system, and/or personal injury.
5Avoid installing this system in a place where foreign objects and liquid might fall. It might cause a fire, damage to this system and/or personal injury. Do not place the following objects on this system:
–Other components, as they may cause damage and/or discoloration on the surface of this system.
–Burning objects (i.e. candles), as they may cause fire, damage to this system, and/or personal injury.
–Containers with liquid in them, as they may cause electrical shock to the user and/or damage to this system.
6Do not cover this system with a newspaper, tablecloth, curtain, etc. in order not to obstruct heat radiation. If the temperature inside this system rises, it may cause fire, damage to this system, and/or personal injury.
7Do not plug in this system to a wall outlet until all connections are complete.
8Do not operate this system
10When disconnecting the power cable from the wall outlet, grasp the plug; do not pull the cable.
11Do not clean this system with chemical solvents; this might damage the finish. Use a clean, dry cloth.
12Only voltage specified on this system must be used. Using this system with a higher voltage than specified is dangerous and may cause fire, damage to this system, and/or personal injury. YAMAHA will not be held responsible for any damage resulting from use of this system with a voltage other than specified.
13To prevent damage by lightning, disconnect the power cable from the wall outlet during an electrical storm.
14Take care of this system so that no foreign objects and/or liquid drops inside this system.
15Do not attempt to modify or fix this system. Contact qualified YAMAHA service personnel when any service is needed. The cabinet should never be opened for any reasons.
16When not planning to use this system for long periods of time (i.e. vacation), disconnect the AC power plug from the wall outlet.
17Be sure to read the “TROUBLESHOOTING GUIDE” section on common operating errors before concluding that this system is faulty.
18Before moving this system, press STANDBY/ON to set this system in the standby mode, and disconnect the AC power plug from the wall outlet.
19VOLTAGE SELECTOR (General model only)The VOLTAGE SELECTOR on the rear panel of
This system is not disconnected from the AC power source as long as it is connected to the wall outlet, even if this system itself is turned off. This state is called the standby mode. In this state, this system is designed to consume a very small quantity of power.
IMPORTANTPlease record the serial number ofTo prevent electric shock, match wide blade of plug to wide slot and fully insert.
This Class B digital apparatus complies with Canadian■For U.K. customers
If the socket outlets in the home are not suitable for the plug supplied with this appliance, it should be cut off and an appropriate 3 pin plug fitted. For details, refer to the instructions described below.
Note•The plug severed from the mains lead must be destroyed, as a plug with bared flexible cord is hazardous if engaged in a live socket outlet.
■Special Instructions for U.K. Model
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE:Blue: NEUTRALBrown: LIVEAs the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth terminal of the three pin plug.
DANGERVisible laser radiation when open. Avoid direct exposure to beam. When this system is plugged to the wall outlet, do not place your eyes close to the opening of the disc tray and other openings to look into inside.
The laser component in this product is capable of emitting radiation exceeding the limit for Class 1.