MIDI Data Format
18
24H rr mm -- Drum High Pass Filter Cutoff Frequency
mm : 00H - 40H - 7FH (-64...0...+63)
30H rr mm -- Drum EQ Bass Gain
mm : 00H - 40H - 7FH (-64...0...+63)
31H rr mm -- Drum EQ Treble Gain
mm : 00H - 40H - 7FH (-64...0...+63)
34H rr mm -- Drum EQ Bass Frequency
mm : 04H - 28H (32...2.0k[Hz])
35H rr mm -- Drum EQ Treble Frequency
mm : 1CH - 3AH (500...16.0k[Hz])
MSB 14H-35H (for drum) is received when the Multi Part parameter PART MODE =
DRUMS1...4.
*1 See 1.2.4
*2 ‘—’ indicates that the value is ignored.
*3 Adjusts the time at which the vibrato effect begins after a note is played. Lower
values will cause the effect to begin applying sooner, and higher values will cause
the effect to begin applying later.
This has no effect when Bank Select MSB=127 is selected.
*4 This has no effect when the Multi Part parameter PART MODE = DRUM or
DRUMS1...4.
1.2.22RPN (Registered Parameter Number)
These messages make part settings such as Pitch Bend Sensitivity and Tuning.
The RPN MSB and RPN LSB are transmitted to specify the parameter which is to be
controlled, and subsequently Data Entry (see 1.2.4) is used to set the value of the speci-
fied parameter.
Control# Parameter Data Range
100 RPN LSB 0...127
101 RPN MSB 0...127
If the Multi Part parameter Rcv RPN = OFF, that part will not receive this message.
The following RPN messages can be received.
RPN Data Entry *1
MSB LSB MSB LSB Parameter name and range of values
00H 00H mm -- *2 Pitch Bend Sensitivity
mm:00H - 18H (0...+24 semitones)
Set in semitone units up to two octaves
00H 01H mm ll Fine Tuning
mm ll: 00H 00H -100 cents
::
mm ll: 40H 00H0 cents
::
mm ll: 7FH 7FH +100 cents
[Note] After mm ll: 00H 7FH (=-87.5) cents comes 01H
00H (=-87.4 cents)
00H 02H mm -- Coarse Tuning
mm:28H - 40H - 58H (-24...0...+24 semitones)
7FH 7FH -- -- RPN Null
Puts the RPN and NRPN numbers in an un-set condition.
The internal setting values will not change.
*1 Refer to 1.2.4.
*2 ‘--’ indicates that the setting value is ignored.
1.2.23Assignable Controller
By specifying a control change number of 0...95 for a part, you can control the way in
which an effect is applied.
For each part, this instrument allows two control change numbers to be specified: AC1
and AC2.
The following parameters specify the effects that are controlled by AC1 and AC2.
• Multi Part Parameter
1. ACI,AC2 PITCH CONTROL
2. ACI,AC2 FILTER CONTROL
3. ACI,AC2 AMPLITUDE CONTROL
4. ACI,AC2 LFO PMOD DEPTH
5. ACI,AC2 LFO FMOD DEPTH
6. ACI,AC2 LFO AMOD DEPTH
• Effectl Parameter
7. ACI,AC2 VARIATION CONTROL DEPTH
(Valid when Variation Effect is assigned to a part as Insertion.)
The AC1 control change number is specified by the Multi Part parameter or A/D Part
parameter AC1 CONTROLLER NUMBER.
The AC2 control change number is specified by the Multi Part parameter or A/D Part
parameter AC2 CONTROLLER NUMBER.
1.3 Channel Mode messages
These messages specify the basic operation of each part.
1.3.1 All Sound Off
Silences all currently sounding notes on the corresponding channel.
However the status of channel messages such as Note-on or Hold On is preserved.
Control# Parameter Data Range
120 All Sound Off 0
1.3.2 Reset All Controllers
The values of the following controllers will change.
Controller Value
Pitch Bend Change +/-0 (center)
Channel Pressure 0 (off)
Polyphonic Key Pressure 0 (off)
Modulation 0 (off)
Expression 127 (maximum)
Hold 0 (off)
Portamento 0 (off)
Sostenuto 0 (off)
Soft Pedal 0 (off)
Portamento Control Reset the Portamento Source Note Number that was re-
ceived
RPN Number un-set, internal data will not change.
NRPN Number un-set, internal data will not change.
The following data will not change
Program Change, Bank Select MSB/LSB, Volume, Pan, Effect Send Levels 1/3/4, and
the value of parameters which were set using RPN and NRPN.
Control# Parameter Data Range
121 Reset All Controllers 0
1.3.3 All Note Off
Turns off all notes which are currently “note-on” for the corresponding channel.
However if Hold1 or Sostenuto are ON, the notes will continue sounding until these are
turned off.
Control# Parameter Data Range
123 All Note Off 0
1.3.4 Omni Off
Performs the same processing as when All Note Off is received.
Control# Parameter Data Range
124 Omni Off 0
1.3.5 Omni On
Performs the same processing as when All Sound Off is received.
Control# Parameter Data Range
125 Omni On 0
1.3.6 Mono
Performs the same processing as when All Sound Off is received, and if the value (mono
number) is within the range of 0...16, sets the corresponding channel to Mode4* (m=1).
Control# Parameter Data Range
126 Mono 0...16
* Mode4 is when only the messages of the specified channel are received, and notes are
sounded monophonically.
1.3.7 Poly
Performs the same processing as when All Note Off is received, and sets the correspond-
ing channel to Mode3*.
Control# Parameter Data Range
127 Poly 0
* Mode3 is when only the messages of the specified channel are received, and notes are
sounded polyphonically.