ADJUSTING THE SPEAKER BALANCE

This procedure lets you adjust the sound output level balance between the main, center and rear speakers by using the built-in test tone generator. When this adjustment is performed, the sound output level heard at the listening position will be the same from each speaker. This is important for the best performance of the digital sound field processor, the Dolby Pro Logic decoder, Dolby Digital decoder and DTS decoder.

Note

•Since this unit cannot enter the test mode while headphones are connected to this unit, be sure to unplug the headphones from the PHONES jack when using the test tone.

Before You Start Adjusting

2

 

 

 

 

 

 

 

 

 

 

 

 

 

1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VOLUME

 

 

 

 

 

 

 

 

 

 

 

 

 

RDS MODE/FREQ

EON

 

STANDBY

 

 

 

 

 

 

 

 

 

 

 

PTY SEEK

 

/ON

 

 

 

 

 

 

 

 

 

 

 

 

MODE

START

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

INPUT MODE

6CH INPUT

 

 

 

 

 

 

 

 

 

 

 

 

 

PRESET

 

 

BASS

 

TREBLE

BALANCE

SPEAKERS

 

 

 

 

 

/TUNING

FM/AM

INPUT

 

 

 

 

 

 

A

B

PROGRAM

 

EFFECT

 

PRESET/TUNING

A/B/C/D/E

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

EDIT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TUNING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MEMORY

MODE

 

–

+

–

+

L

R

ON

OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MAN'L/AUTO FM

AUTO/MAN'L MONO

 

 

 

 

 

 

 

 

 

PHONES

S VIDEO

VIDEO

L AUDIO R

OPTICAL

 

 

 

 

 

 

 

 

 

 

 

SILENT

 

VIDEO AUX

 

 

 

 

 

 

4

 

 

3

 

 

 

 

 

 

 

 

1 Set the volume at the

VOLUME

minimum level.

 

2 Turn the power on.

STANDBY

/ON

3 Press SPEAKERS A or B

SPEAKERS

 

A B

to select the main speakers to be used.

ON

If you use two main speaker systems, press both A and B.

4 Set BASS, TREBLE and BALANCE to the center position.

BASSTREBLEBALANCE

–

+

–

+

L

R

Using the Test Tone

The adjustment of each speaker sound output level should be performed at your listening position with the remote control.

1

3

5

PREPARATION

 

2,6

1 Press AMP(TUNER) on the component selector.

2 Press TEST.

“TEST LEFT” appears on the display.

3 Turn up the volume.

You will hear a test tone (like pink noise) from each speaker for about two seconds in following order: left main speaker, center speaker, right main speaker, right rear speaker and left rear speaker. The display changes as shown below.

TEST TEST

LEFT RIGHT

TEST CENTER

TEST L SUR.

TEST R SUR.

Notes

•If the test tone cannot be heard, turn down the volume, set the unit in the standby mode and check the speaker connections.

•If the test tone cannot be heard from the center speaker, check the setting of “CENTER SP” in the SET MENU.

English

19