Yamaha RX-V520RDS 57

			TROUBLESHOOTING

	Problem	Cause	Remedy	Refer to
	Problem	Cause	Remedy	page
				page

	The volume level cannot	The component connected to the REC OUT	Turn on the power to the component.	—
	be increased, or the	jacks of this unit is turned off.
	sound is distorted.
	The effect and surround	It is not possible to record the effect and		34
	sounds cannot be	surround sounds by a recording component.
	recorded.

	A source cannot be	A source component is only connected to the	Connect the source component to the digital	12 – 15
	recorded by a digital	analog input jacks of this unit.	input jacks of this unit.
	recording component
	connected to the
	DIGITAL OUTPUT jack of
	this unit.

	The settings of the SET	“9 MEM. GUARD” in the SET MENU is set	Select OFF.	39
	MENU and some other	to ON.
	settings on this unit
	cannot be changed.

	This unit does not	The internal microcomputer has been frozen by	Disconnect the AC power cord from the outlet	—
	operate properly.	an external electric shock (such as lightning or	and then plug it in again after about 30 seconds.
		excessive static electricity) or by a power
		supply with low voltage.

	The sound is degraded	This unit is in the standby mode.	Turn on the power of the unit.	—
	when listening with
	headphones connected
	to a tape deck or CD
	player that is connected
	to this unit.
	There is noise	The unit is too close to the digital or high-	Move the unit further away from such	—
	interference from digital	frequency equipment.	equipment.
	or high-frequency
	equipment, or the unit.

APPENDIX

English

55

Contents

Natural Sound AV Receiver Ampli-tuner audio-vidéo CAUTION: READ THIS BEFORE OPERATING YOUR UNIT CONTENTS FEATURES GETTING STARTED Checking the Package Contents Battery Installation in the Remote Control Battery Replacement CONTROLS AND FUNCTIONS Front Panel Page Remote Control Using the Remote Control Display Rear Panel SPEAKER SETUP Speakers to Be Used Speaker Placement CONNECTIONS Before Connecting Components Connecting Audio Components Connecting an External Decoder Page Connecting Video Components Page Connecting Speakers ■Subwoofer connection IMPEDANCE SELECTOR Switch Connecting the Power Supply Cords ADJUSTING THE SPEAKER BALANCE Before You Start Adjusting Using the Test Tone Page PLAYING A SOURCE ■To mute the sound ■When you have finished using this unit ■Notes on the digital signal ■BGV (background video) function Input Modes and Indications Selecting a DSP Program Canceling the Sound Effect (turning off the effect speakers) TUNING Connecting the Antennas Automatic Tuning Manual Tuning Automatic Preset Tuning (for RDS stations only) Manual Preset Tuning To Recall a Preset Station Exchanging Preset Stations RECEIVING RDS STATIONS Description of RDS Data Changing the RDS Mode PTY SEEK Function EON Function RECORDING A SOURCE SET MENU Adjusting the Items on the SET MENU 1SPEAKER SET (speaker mode settings) 2HP TONE CTRL (headphone tone control) 3 I/O ASSIGN 4 INPUT MODE (initial input mode) 5 DOLBY D. SET (Dolby Digital set) 6 DTS SET (DTS LFE level) 7 SP DLY TIME (center delay) 8DISPLAY SET 9 MEM. GUARD (memory guard) DELAY TIME AND SPEAKER OUTPUT LEVELS Delay Time Sound Output Level of the Center Right Rear and Left Rear Speakers and Subwoofer Adjusting Method SLEEP TIMER Setting the SLEEP Timer Canceling the SLEEP Timer PRESET REMOTE CONTROL Component Selector Buttons Controlling the Components Connected to This Unit Description of Each Mode ■CD MODE ■DVD/LD MODE ■DVD MENU MODE ■ VCR MODE ■ CBL/SAT MODE ■TV MODE Setting the Manufacturer Code Returning to the Factory Setting SOUND FIELD PROGRAM Hi-FiDSP Programs CINEMA DSP Programs ■For movie programs: Nos. 7 to ■MOVIE THEATER 1 and TROUBLESHOOTING Page Page ■Tuner ■Remote control SPECIFICATIONS GLOSSARY ■S VIDEO signal ■PCM (Linear PCM) ■Sampling frequency and number of quantized bits ■I/O ASSIGN (SET MENU) INDEX Page Page Page Page Page Page L Analog signal O Optical signal S Video signal Video signal Signal flow