Troubleshooting

Problem

Cause

Remedy

See

page

 

 

 

 

 

 

 

Sound is heard from

Incorrect cable connections.

Connect the cables properly. If the problem persists,

11-14

the speaker on one

 

the cables may be defective.

 

side only.

 

 

 

Incorrect settings in “SP LEVEL.”

Adjust the “SP LEVEL” settings.

33

 

 

 

 

 

Only the center

When playing a monaural source with a

 

 

speaker outputs

CINEMA DSP program, the source signal

 

 

substantial sound.

is directed to the center channel, and the

 

 

 

front and surround speakers output effect

 

 

 

sounds.

 

 

 

 

 

 

No sound is heard

“CENTER” in “SPEAKER SET” is set to

Set “CENTER” to “SML” or “LRG.”

32

from the center

“NONE.”

 

 

speaker.

 

 

 

Some sound field programs do not output

Try another sound field program.

25

 

 

sounds from the center speaker.

 

 

 

 

 

 

No sound is heard

“SUR. LR” in “SPEAKER SET” is set to

Set “SUR. LR” to “SML” or “LRG.”

32

from the surround

“NONE.”

 

 

speakers.

 

 

 

This unit is in the “STRAIGHT” mode

Press MSTRAIGHT on the front panel so that

26

 

 

and a monaural source is being played

“STRAIGHT” disappears from the front panel

 

 

back.

display.

 

 

 

 

 

No sound is heard

“BASS OUT” in “SPEAKER SET” is set

Set “BASS OUT” to “SWFR” or “BOTH.”

32

from the subwoofer.

to “FRNT” when a Dolby Digital or DTS

 

 

 

signal is being played.

 

 

 

 

 

 

 

“BASS OUT” in “SPEAKER SET” is set

Set “BASS OUT” to “BOTH.”

32

 

to “SWFR” or “FRNT” when a 2-channel

 

 

 

source is being played.

 

 

 

 

 

 

 

The source does not contain low-

 

 

 

frequency bass signals.

 

 

 

 

 

 

Dolby Digital or DTS

The connected component is not set to

Make an appropriate setting following the operating

—

sources cannot be

output Dolby Digital or DTS digital

instructions for your component.

 

played. (Dolby Digital

signals.

 

 

or DTS indicator on

 

 

 

Audio input jack select is set to

Set Audio input jack select to “AUTO.”

18

the front panel

“ANALOG.”

 

 

display does not light

 

 

 

 

 

up.)

 

 

 

 

 

 

 

A humming sound is

Incorrect cable connections.

Connect the audio cables firmly. If the problem

—

heard.

 

persists, the cables may be defective.

 

 

 

 

 

The volume level

You are attempting to set the volume level

Adjust “MAX VOL.” setting.

34

cannot be increased,

higher than the maximum volume level.

 

 

or the sound is

 

 

 

The component connected to the AUDIO

Turn on the power of the component.

—

distorted.

OUT (REC) jack on this unit is turned off.

 

 

 

 

 

 

 

 

 

The sound effect

It is not possible to record the sound effect

 

 

cannot be recorded.

with a recording component.

 

 

 

 

 

 

A source cannot be

The source component is not connected to

Connect the source component to the analog AUDIO

13

recorded by an

the analog AUDIO IN jacks on this unit.

IN jacks.

 

analog component

 

 

 

connected to the

AUDIO OUT (REC) jack.

42 En