3 Carry out the AUTO SETUP (IntelliBeam)
Carry out the AUTO SETUP to adjust the settings that best match your listening environment
The IntelliBeam technology allows you to achieve sound adjustments that best match your listening environment. It is normal for loud test tones to be output during the AUTO SETUP procedure. Make sure that there are no children around in the listening room while the AUTO SETUP procedure is in progress.
CH LEVELMENU
The following screen appears on the TV. Leave the room within 10 seconds before the AUTO SETUP procedure starts.
4 | Enjoying surround sound |
For instructions on how to operate or set your TV or DVD player, refer to the owner’s manual supplied with each component.
| Enjoying DVDs in surround sound | Enjoying TV in surround sound |
You may want to use the supplied cardboard microphone stand for the AUTO SETUP. Assemble the stand and place the IntelliBeam microphone on top of it as shown below.
1 | 2 | 3 | 4 |
INTELLIBEAM MIC | INPUT | VOLUME | STANDBY/ON |
INTELLIBEAM MIC
IntelliBeam microphone (supplied)
Cardboard microphone stand (supplied) 
| TV/AV |
| ENTER |
| YSP |
TEST | RETURN |
If the menu screen does not appear, check the OSD video pin cable (see the connection example on the front page).
| TV | MACRO | AUTO SETUP | |
| INPUT1 INPUT2 |
| ||
TV |
|
| PREPARATION & CHECK | |
| AUTO |
| Please connect the MIC. | |
|
| Please place the MIC at least | ||
VOL MODE | SETUP INPUTMODE SLEEP | |||
1.8m/6ft away from the YSP | ||||
|
|
| ||
|
|
| unit. The MIC should be set | |
5BEAM | ST+3BEAM | 3BEAM | at ear level when seated. | |
Measurement takes about 3min. | ||||
1 | 2 | 3 | After [ENTER] is pressed, | |
please leave the room. | ||||
[ENTER]:Start [RETURN]:Cancel
CH LEVEL | MENU | AUTO SETUP START |
|
| |
|
| Will begin in 10sec |
| TV/AV | Please leave the room |
| ENTER |
|
| YSP | |
|
| |
TEST | RETURN | [RETURN]:Cancel |
|
When the AUTO SETUP procedure is completed, the following screen appears on the TV.
SHOW RESULTMEASUREMENT COMPLETE
BEAM MODE :5 BEAM
SUBWOOFER :NOT APPLICABLE
[ENTER]:Save
If “ENVIRONMENT CHECK (FAILED) is displayed, see page 36 in the Owner’s Manual and then run the procedure again.
to YSP.
This unit switches to the YSP operation mode.
TV/AV
ENTER
YSP
TEST | RETURN |
2Set the operation mode selector
to YSP.
This unit switches to the YSP operation mode.
TV/AV
ENTER
YSP
TEST | RETURN |
Use the supplied cardboard microphone stand or a tripod to place the IntelliBeam microphone at the same height as your ears would be when you are seated.
yHint
| • The result may differ depending on the environment. |
| • If any error occurs, the corresponding error message appears |
IntelliBeam microphone
Center height of
this unit
Cardboard
microphone stand
Upper bound
position of the
microphone
Within 1 m |
|
|
(3.3 ft) |
|
|
Within 1 m | Center line |
|
(3.3 ft) |
| |
Listening | Cardboard | IntelliBeam |
position | microphone |
Place the IntelliBeam microphone on the extended center line of this unit and 1.8 m (6.0 ft) or more away from it. Also, make sure place the IntelliBeam microphone within 1 m (3.3 ft) upper or lower from the center height of this unit.
•Is the microphone placed within 1 m (3.3 ft) upper or lower from the center height of this unit?
•Is the microphone placed more than 1.8 m (6.0 ft) from thefront of this unit?About the room environment• Is your listening room kept as quiet as possible?| on the screen. In this case, see “Error messages for AUTO |
| SETUP” on page 37 in the Owner’s Manual and then follow |
| the instructions. To start the AUTO SETUP procedure once |
| again, press RETURN. |
The following screen appears on the TV for 2 seconds and then the menu screen disappears from the TV.
STB VCR DVD AUX
TV
INPUT1 INPUT2 MACRO
TV
2)Play back the supplied demonstration DVD on the DVD player.STB VCR DVD AUX
TV
INPUT1 INPUT2 MACRO
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM ST+3BEAM 3BEAM
1 2 3
More than 1.8 m (6.0 ft)
Lower bound position | microphone |
stand | |
of the microphone |
|
The best setting may not be done if you are in the room. Prepare to leave the room in 10 seconds after pressing ENTER in step 10.
CH LEVEL | MENU |
| |
|
| AUTO SETUP COMPLETE | |
| TV/AV | Please remove the MIC from | |
ENTER | the YSP and the listening | ||
| |||
| YSP | position. | |
|
|
The MULTI indicator and/or (see page 42 in the Owner’s Manual) is lit in the front panel display. If the sound is output from your TV speakers, mute the volume on your TV. For details about digital audio input signals, see page 46 in the Owner’s Manual.
4
yHint
| • When leaving the room, bring this guide with you. |
| • Wait outside the room during the AUTO SETUP procedure. |
TEST | RETURN |
VOLUME | CH | TV VOL |
Before operations, insert batteries into the remote control (see page 26 in the Owner’s Manual).
If necessary, adjust the volume level of this unit.If you have connected the subwoofer, set the volume and crossover/high cut frequency. Refer to the note on page 32 in the Owner’s Manual.
Subwoofer
VOLUME | CROSSOVER/ |
| HIGH CUT |
STANDBY/ON | POWER POWER |
AV TV
MIN | MAX | MIN | MAX |
5
| • The AUTO SETUP procedure takes about 3 minutes. |
| • To cancel the AUTO SETUP procedure after it is started, |
| press RETURN. |
INTELLIBEAM MIC | INPUT | VOLUME | STANDBY/ON |
5Press VOLUME +/- on the remote control to adjust the volume level of this unit.
6Press one of the beam mode buttons on the remote controlto select the desired beam mode.Select one of the six beam modes that best matches the current input source of this unit. For further information on the beam modes, see page 44 in the Owner’s Manual.
MUTE | TV INPUT TV MUTE |
5BEAM ST+3BEAM 3BEAM
1 2 3
STEREO MY BEAM MY SUR.
4 5 6
INTELLIBEAM MIC
To