AUTO SETUP (IntelliBeam)

■Error messages for AUTO SETUP

Before the AUTO SETUP procedure starts

Error message

Cause

Remedy

See

page

 

 

 

 

 

 

 

ERROR E-2

The IntelliBeam microphone is not

Connect the IntelliBeam microphone to

32

No MIC detected. Please check

connected to this unit.

this unit.

 

MIC connection and re-try.

 

 

 

 

 

 

 

While the AUTO SETUP procedure is in progress

If one of the errors listed below except E-1 is displayed, press RETURN. In case you have started the AUTO SETUP procedure by pressing AUTO SETUP in step 3, run the procedure again from step 3 after the screen disappears. In case you have started the AUTO SETUP procedure by pressing MENU in step 3, run the procedure again from step 4 after the screen in step 3 is displayed. Run MANUAL SETUP if the problem is difficult to be saved.

Error message

Cause

Remedy

See

 

 

page

 

 

 

 

 

 

 

 

 

 

 

 

 

ERROR E-1

There is too much unwanted noise in

Make sure that your listening room is as

—

 

 

Please test in quieter environment.

your listening room.

quiet as possible. You may want to

 

 

 

 

 

choose certain hours during the day

 

 

 

 

 

 

 

 

 

 

when there is not much noise coming

 

 

 

 

 

from outside.

 

 

SETUP

 

 

 

 

 

ERROR E-2

The IntelliBeam microphone was

Make sure that the IntelliBeam

32

 

 

 

No MIC detected. Please check

disconnected while the AUTO SETUP

microphone is firmly connected to this

 

 

 

MIC connection and re-try.

procedure was in progress.

unit.

 

 

 

 

 

 

 

 

 

ERROR E-3

Some other operations were performed

Do not perform any other operations

—

 

 

Unexpected control is detected.

on this unit while the AUTO SETUP

while the AUTO SETUP procedure is in

 

 

 

 

 

 

Please re-try.

procedure was in progress.

progress.

 

 

 

 

 

 

 

 

 

ERROR E-4

The IntelliBeam microphone is not

Make sure that the IntelliBeam

32

 

 

Please check MIC position. MIC

placed in front of this unit.

microphone is installed in front of this

 

 

 

should be set in front of YSP.

 

unit.

 

 

 

 

 

 

 

 

 

ERROR E-5

The IntelliBeam microphone is not

Make sure that the IntelliBeam

32

 

 

Please check MIC position. MIC

placed in the right distance from this

microphone is installed more than 1.8 m

 

 

 

should be set above 1.8m/6.0ft.

unit.

(6.0 ft) from the front of this unit and

 

 

 

 

 

within 1 m (3.3 ft) from the center height

 

 

 

 

 

of this unit.

 

 

 

 

 

 

 

 

 

ERROR E-6

The IntelliBeam microphone cannot

Make sure that the IntelliBeam

32

 

 

Volume level is lower than

collect the sound produced by this unit

microphone is firmly connected to this

 

 

 

expected. Please check MIC

because the sound output level is too low.

unit and placed in a proper location. If

 

 

 

position/connection and re-try.

 

the problem persists, contact the nearest

 

 

 

 

 

authorized Yamaha service center for

 

 

 

 

 

assistance.

 

 

 

 

 

 

 

 

 

ERROR E-7

An internal system error occurred.

Repeat the AUTO SETUP procedure.

—

 

 

Unexpected error happened.

 

 

 

 

 

Please re-try.

 

 

 

 

 

 

 

 

 

 

 

English

37 En