Control range (from this unit): 1.8 m to 9.0 m (6.0 ft

3 Configure “BEAM TRAVEL LENGTH”.

to 30.0 ft)

 

 

Adjust the distance that sound beams travel after

Control range (from left wall): 0.6 m to 11.4 m (2.0 ft

being output and reflected off the wall until they

to 38.0 ft)

 

 

arrive at the listening position so that all sounds can

 

 

 

FLAT TO WALL

arrive at the listening position at the same time.

 

0.6 to 11.4 m

Note

 

• Configure this setting only when you have adjusted

1.8 to 9.0 m

(2.0 to 38.0 ft)

“HORIZONTAL ANGLE”.

 

(6.0 to 30.0 ft)

 

 

Control range: 0.3 m to 24.0 m (1.0 ft to 80.0 ft)

 

 

 

 

The length of each

■ BEAM ADJUSTMENT (Beam adjustment)

arrow indicates the

 

 

beam travel length.

SET MENU → MANUAL SETUP → BEAM

 

ADJUSTMENT

Use to manually adjust the various sound beam settings.

Notes

 

4 Configure “FOCAL LENGTH”.

PREPARATION INTRODUCTION

• The “BEAM ADJUSTMENT” parameters are automatically

adjusted (except “Center” in “FOCAL LENGTH”) if you run

the AUTO SETUP (page 15) or if you configure “SETTING

PARAMETERS” (page 34).

• Depending on the beam mode settings (page 23), some channel

positions may not be available for selection. In this case, “– –”

is displayed.

• If you change "BEAM ADJUSTMENT" settings while playing

Adjust the distance from the front of this unit to the focal point of output for each channel to achieve an expansive feeling for each channel. Adjust toward - (minus) to move the focus outward (widen the sweet spot) and adjust toward + (plus) to move the focus toward the normal position (narrow the sweet spot).

PLAYBACK

back your iPod/iPhone connected to PDX-50TX, the subwoofer

connected to SWK-W10 outputs the iPod/iPhone audio. We

recommend stopping the iPod/iPhone playback during the beam

adjustment.

1 Configure “HORIZONTAL ANGLE”.

Adjust the horizontal angle of sound beams for each

channel using test tones.

Adjust toward L (left) to move the direction of the

Focal point

Focal length

Sweet

spot

FEATURES

output to the left and adjust toward R (right) to move

it to the right.

Control range: L90° to R90°

(–)(+)

(+)(–)

Control range: –1.0 m to +13.0 m (–3.5 ft to +43.5 ft)

y

•We recommend that you use the initial setting (–0.5 m or – 1.5 ft) for “Center”.

•The width of the sweet spot becomes slightly wider than the width of this unit if you run the AUTO SETUP (page 15) or if you configure “SETTING PARAMETERS” (page 34).

Example

 

Front left channel

Center channel

Customizing this unit (SET MENU)

System

configurations

(ADVANCED SETUP)

y

• Press G to switch the channels.

2Configure “VERTICAL ANGLE”.

Adjust the vertical angle of sound beams for each channel using test tones.

Adjust toward – (minus) to move the angle downward and adjust toward + (plus) to move the angle upward. Control range: –45° to +45°

(+)

0°

(–)

（－）

（＋）

■IMAGE LOCATION (Image location)

SET MENU → MANUAL SETUP → IMAGE

LOCATION

Use to adjust the direction from which the front left and right channel sound is heard so that each sound can be heard closer to the center channel.

Use this feature to redirect audio signals if the sound coming from the front left and right channels seems unnatural.

Using an external

amplifier

Controlling external

components

SETTINGS

APPENDIX

35 En