You can adjust this parameter only when “5BeamPlus2”, “5 Beam” or “3 Beam” is selected in “BEAM MODE” (page 23).

y

•To adjust the volume of each channel, see “CHANNEL LEVEL” (page 37)

Choices: OFF*, ON

• Select “ON” to configure the sound direction.

1Adjust the image location for the front left channel (LEFT).

The higher the percentage, the louder the output from the center

 

 

 

With the front left

 

 

Without adjustment

 

channel adjusted

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2Adjust the image location for the front right channel (RIGHT).

The higher the percentage, the louder the output from the center

 

 

With the front right

Without adjustment

 

channel adjusted

 

 

 

 

 

 

SOUND SET MENU

■TONE CONTROL (Tone control)
SET MENU → SOUND SET MENU → TONE
CONTROL

Use to adjust the tonal quality of sound beams.

TREBLE (Treble)

Use to adjust the high-frequency response.

Choices: –10.0 dB to +10.0 dB

Initial setting: 0.0 dB

BASS (Bass)

Use to adjust the low-frequency response.

Choices: –10.0 dB to +10.0 dB

Initial setting: 0.0 dB

■SUBWOOFER SET (Subwoofer settings)
SET MENU → SOUND SET MENU →
SUBWOOFER SET

Use to configure the subwoofer settings.

BASS OUT (Bass out)

Select where to output low-frequency effect (LFE) and low-frequency (bass) signals.

Choices: SUBWOOFER, FRONT OR AUTO*

•Select SUBWOOFER if you connect a subwoofer with a subwoofer cable. LFE and low-frequency signals from other channels are directed to the subwoofer.

•Select FRONT OR AUTO if you do not use a subwoofer or connect a subwoofer by wireless. LFE and low-frequency signals from other channels are directed to the front right and left channels when you do not use a subwoofer. They are directed to the subwoofer automatically when a wireless connection between a subwoofer and this unit is established properly. If the wireless connection is cut off, they are directed to the front channels automatically.

CROSS OVER (Crossover)

When “BASS OUT” is set to “SUBWOOFER”, you can use this feature to select a crossover (cutoff) frequency for all low-frequency signals. All frequencies below the selected frequency will be sent to the subwoofer position. Choices: 80Hz, 100Hz, 120Hz*

LFE LEVEL (Low-frequency effect level)

Adjust the output level of the low-frequency effect (LFE) channel according to the capacity of your subwoofer. This setting is effective only when this unit decodes Dolby Digital or DTS signals.

Choices: –20 dB to 0 dB*

DISTANCE (Distance)

Adjust the distance of the subwoofer from the listening position.

Choices: 0.3 m to 15.0 m (1.0 ft to 50.0 ft)

Initial setting: 3.0 m (10.0 ft)

■AUDIO DELAY (Audio delay)
SET MENU → SOUND SET MENU → AUDIO
DELAY

Use to adjust delay in output timing between video signals and audio signals.

AUTO LIP SYNC (Automatic lipsync)

Select whether to automatically adjust the audio output delay when a TV that supports the automatic lipsync is connected to the HDMI OUT jack of this unit.

Choices: ON*, OFF

•Select ON if the TV connected to the HDMI OUT jack of this unit supports the automatic lipsync. The audio output delay is automatically adjusted.

•Select OFF if the TV connected to the HDMI OUT jack of this unit does not support the automatic lipsync or you want to disable the automatic lipsync. You can manually adjust the audio output delay in “HDMI”.

TV

Adjust the audio output delay applied to signals input from the TV jacks.

Control range: 0 msec* to 400 msec

HDMI

Manually adjust the audio output delay applied to signals input from the HDMI IN jacks. This setting is effective only when “AUTO LIP SYNC” is set to “OFF” Control range: 0 msec to 400 msec

Initial setting: 30msec

AUX1/2

Adjust the audio output delay applied to signals input from the AUX1/2 jacks.

Control range: 0 msec to 400 msec

Initial setting: 30msec

36 En