2

Press G

/

to select “AUTO SETUP” and

 

y

 

then press GENTER.

 

• If “ENVIRONMENT CHECK [FAILED]” is displayed,

 

 

refer to “Error messages for AUTO SETUP” (page 18),

 

 

 

 

 

 

 

 

 

 

press IRETURN, and then run the AUTO SETUP

 

 

 

B)AUTO SETUP

 

procedure again.

 

 

 

 

• If “SUBWOOFER :NOT APPLICABLE” is displayed

 

 

 

 

 

 

 

1)BEAM+SOUND OPTIMZ

 

even though a subwoofer is connected to this unit and

 

 

2)BEAM OPTIMZ ONLY

 

 

 

 

turned on, check the connection and then increase the

 

 

3)SOUND OPTIMZ ONLY

 

 

 

 

 

 

volume level of the subwoofer and run the AUTO SETUP

 

 

 

 

 

procedure again.

 

 

 

[p]/[p]:Up/Down

 

• Depending on the environment of your listening room, the

 

 

 

[ENTER]:Enter

 

beam angles of front right and left and surround left and

 

 

 

 

 

 

 

 

 

 

right may be set to the same value even if “BEAM MODE

 

 

 

 

 

:5 BEAM” is displayed as a result.

3

Press G

/

to select “BEAM+SOUND

 

 

 

OPTIMZ”, “BEAM OPTIMZ ONLY” or “SOUND

 

 

 

OPTIMZ ONLY” and then press GENTER.

 

6 Press GENTER to confirm the results.

 

 

 

 

 

The menu screen disappears in two seconds.

 

 

 

AUTO SETUP

 

 

 

 

PREPARATION & CHECK

 

 

 

Please connect the MIC.

 

 

 

Please place the MIC at least

 

 

 

1.8m/6ft away from the unit.

 

AUTO SETUP COMPLETE

 

The MIC should be set

 

 

 

at ear level when seated.

 

Please remove the MIC from

 

Measurement takes about 3min.

 

the unit and the listening

 

After [ENTER] is pressed,

 

position.

 

please leave the room.

 

 

 

[ENTER]:Start [RETURN]:Cancel

 

 

 

 

 

4 Prepare to leave the room.

 

 

 

The best setting may not be done if you are in the

 

y

 

room. Prepare to leave the room in 10 seconds after

 

• If you do not want to reflect the results, press IRETURN.

pressing GENTER in step 5.

7 Disconnect the IntelliBeam microphone.

y

•Wait outside the room during the AUTO SETUP procedure.

•The AUTO SETUP procedure takes about 3 minutes.

•To cancel the AUTO SETUP procedure after it is started, press IRETURN.

5 Press GENTER to start the AUTO SETUP

 

procedure and then leave the room within 10

 

seconds.

The measurement results are stored in the internal

 

AUTO SETUP START

memory of this unit until you run the AUTO SETUP

procedure again or configure the settings manually.

Will begin in 10sec

 

Please leave the room

 

**--------

 

[RETURN]:Cancel

 

The setup screen automatically changes during the

 

AUTO SETUP procedure.

 

If an error occurs, an error buzzer sounds and an error

 

message is displayed. For details on error messages,

 

see “Error messages for AUTO SETUP” (page 18).

 

If the AUTO SETUP procedure is complete, this unit

 

rings the chimes.

 

XXXXXXXXSHOW RESULTXXXXXXXXXX

 

MEASUREMENT COMPLETE

 

BEAM MODE :5Beam/Plus2

 

SUBWOOFER :YES

 

[ENTER]:Save set-up.

 

[RETURN]:Do not save set-up.

 

Changing OSD

language

AUTO SETUP (IntelliBeam)

Using the system

memory

PREPARATION INTRODUCTION

FEATURES PLAYBACK

SETTINGS

APPENDIX

17 En