TV

 

AV

 

TV

 

AUX 1

AUX 2

HDMI 1

 

HDMI 2

HDMI 3

HDMI 4

 

iPod

RADIO

 

 

ENTER

 

MOVIE

MUSIC TAINMENT

OFF

 

 

CINEMA DSP

 

SURROUND

STEREO

 

ENTER

 

G

TOP MENU

 

MENU

 

OPTION

SETUP

RETURN

I

TV VOL

CH

VOLUME

 

TV

TV

 

 

MUTE

INPUT

MUTE

 

UNIVOLUME

SUR. DECODE

INTELLIBEAM

 

1

2

3

 

4

5

6

 

7

8

9

 

0

+10

ENT

 

CODE SET

 

 

 

TUNING

PRESET

CATEGORY

 

INFO

MEMORY

SLEEP

 

GENTER

G /

IRETURN

ISETUP

■Error messages for AUTO SETUP

If an error message is displayed on your TV, check the error message list to solve the problem and then follow the procedure below.

[ERROR E-1]: Press GENTER to run the AUTO SETUP procedure again or IRETURN to cancel the operation

Other errors: Press IRETURN to cancel the operation and then run the AUTO SETUP procedure again.

Note

If the problem is difficult to be solved, configure the settings manually in “MANUAL SETUP” (page 34).

Error message

Cause

Remedy

See

page

 

 

 

 

 

 

 

ERROR E-1

There is too much unwanted noise in

Make sure that your listening room is as

—

Please test in quieter environment.

your listening room.

quiet as possible. You may want to

 

 

 

choose certain hours during the day

 

 

 

when there is not much noise coming

 

 

 

from outside.

 

 

 

 

 

ERROR E-2

The IntelliBeam microphone is not

Connect the IntelliBeam microphone to

15

No MIC detected. Please check

connected to this unit or disconnected

this unit firmly.

 

MIC connection and re-try.

during the AUTO SETUP procedure.

 

 

 

 

 

 

ERROR E-3

Some other operations were performed

Do not perform any other operations

—

Unexpected control is detected.

on this unit while the AUTO SETUP

while the AUTO SETUP procedure is in

 

Please re-try.

procedure was in progress.

progress.

 

 

 

 

 

ERROR E-4

The IntelliBeam microphone is not

Make sure that the IntelliBeam

15

Please check MIC position. MIC

placed in front of this unit.

microphone is installed in front of this

 

should be set in front of the unit

 

unit.

 

and re-try.

 

 

 

 

 

 

 

ERROR E-5

The IntelliBeam microphone is not

Make sure that the IntelliBeam

15

Please check MIC position. MIC

placed in the right distance from this

microphone is installed more than 1.8 m

 

should be set above 1.8m/6.0ft and

unit.

(6.0 ft) from the front of this unit and

 

re-try.

 

within 1 m (3.3 ft) from the center height

 

 

 

of this unit.

 

 

 

 

 

ERROR E-6

The IntelliBeam microphone cannot

Make sure that the IntelliBeam

15

Volume level is lower than

collect the sound produced by this unit

microphone is firmly connected to this

 

expected. Please check MIC

because the sound output level is too low.

unit and placed in a proper location. If

 

position/connection and re-try.

 

the problem persists, contact the nearest

 

 

 

authorized Yamaha service center for

 

 

 

assistance.

 

 

 

 

 

ERROR E-7

An internal system error occurred.

Repeat the AUTO SETUP procedure.

—

Unexpected error happened.

 

 

 

Please re-try.

 

 

 

 

 

 

 

18 En