TV

 

AV

 

TV

 

AUX 1

AUX 2

HDMI 1

 

HDMI 2

HDMI 3

HDMI 4

 

iPod

RADIO

 

 

ENTER

 

MOVIE

MUSIC TAINMENT

OFF

 

 

CINEMA DSP

 

SURROUND

STEREO

 

ENTER

 

G

TOP MENU

 

MENU

 

OPTION

SETUP

RETURN

I

TV VOL

CH

VOLUME

 

TV

TV

 

 

MUTE

INPUT

MUTE

 

UNIVOLUME

SUR. DECODE

INTELLIBEAM

 

1

2

3

 

4

5

6

 

7

8

9

 

0

+10

ENT

 

CODE SET

 

 

 

TUNING

PRESET

CATEGORY

 

INFO

MEMORY

SLEEP

 

GENTER

G /

G /

G

IRETURN

38 En

SOUND OUT (Sound output redirection)

Use to redirect the output of audio signals. Audio output of all the channels switches simultaneously.

Choices: SPEAKER*, PRE OUT

•Select SPEAKER to output sounds from this unit.

•Select PRE OUT to output audio signals from the PRE OUT jacks of this unit. You also need to configure the parameters from “BASS OUT” to “LFE Level” described below.

y

•The parameters from “BASS OUT” to “LFE Level” are settings for the PRE OUT jacks when they are selected as audio output jacks.

BASS OUT (Bass sound output redirection)

Use to redirect the output of bass sounds. The settings under “BASS OUT” are for the PRE OUT jacks. Choices: SUBWOOFER, FRONT*

•Select SUBWOOFER to output bass sounds from the subwoofer.

•Select FRONT to output bass sounds from the external front right and left speakers.

Front SP Size (Front speaker size for PRE OUT)

Select the size of external front speakers.

Choices: Small, Large*

•Select Small if the diameter of the front speaker’s woofer is smaller than 16 cm. Low-frequency parts of front right and left channel signals are output from the subwoofer.

Center SP Size (Center speaker size for PRE OUT)

Select the size of external center speakers.

Choices: None, Small*

•Select None if no center speaker is used. Center channel signals are mixed into the front right and left speakers.

•Select Small if a center speaker is used. Low-frequency parts of center channel signals are output from the subwoofer (or mixed into the front right and left channel signals if subwoofer is not available).

PRE OUT Volume (PRE OUT volume)

Adjust the output level of the PRE OUT jacks. Control range: –30.0 dB to 0.0 dB

Initial setting: –18.0 dB

LFE Level (Low-frequency effect level for PRE OUT)

Adjust the low-frequency effect output level of the PRE OUT jacks. This setting is effective only when this unit decodes Dolby Digital or DTS signals.

Control range: –20 dB to + 0 dB*

INPUT MENU

■INPUT ASSIGNMENT (Input assignment)
SET MENU → INPUT MENU → INPUT
ASSIGNMENT

Use to change the key assignments of input jacks on this unit. The parenthetic references displayed in the menu screen indicate the initial settings.

See also: “AUDIO SELECT” (page 39)

y

• Press G to proceed to the next page.

AUDIO1

Select the key to which the AUDIO IN (TV) jacks are assigned.

Choices: TV*, AUX1, AUX2, HDMI1, HDMI2, HDMI3, HDMI4

Note

•The input already selected in “AUDIO2” is not displayed. To set the input selected in “AUDIO2”, change “AUDIO2” parameter, and then reconfigure.

AUDIO2

Select the key to which the AUDIO IN (AUX 1) jacks are assigned.

Choices: AUX1*, AUX2, HDMI1, HDMI2, HDMI3, HDMI4, TV

Note

•The input already selected in “AUDIO1” is not displayed. To set the input selected in “AUDIO1”, change “AUDIO1” parameter, and then reconfigure.

OPTICAL1

Select the key to which the DIGITAL IN (TV) jack is assigned.

Choices: TV*, AUX1, AUX2, HDMI1, HDMI2, HDMI3, HDMI4

Note

•The input already selected in “OPTICAL2” or “COAX” is not displayed. To set the input selected in one of these parameters, change the corresponding parameter, and then reconfigure.

OPTICAL2

Select the key to which the DIGITAL IN (AUX 1) jack is assigned.

Choices: AUX1*, AUX2, HDMI1, HDMI2, HDMI3, HDMI4, TV

Note

•The input already selected in “OPTICAL1” or “COAX” is not displayed. To set the input selected in one of these parameters, change the corresponding parameter, and then reconfigure.

COAX

Select the key to which the DIGITAL IN (AUX 2) jack is assigned.

Choices: AUX2*, HDMI1, HDMI2, HDMI3, HDMI4, TV, AUX1

Note

•The input already selected in “OPTICAL1” or “OPTICAL2” is not displayed. To set the input selected in one of these parameters, change the corresponding parameter, and then reconfigure.

■INPUT RENAME (Input rename)
SET MENU → INPUT MENU → INPUT RENAME

Use to change the name of the input source displayed when the input source is selected. Select a name from templates, or enter an original name.

Selecting a name from templates
1Press G / to select the input source to be renamed.