TV |
| AV |
|
TV |
| AUX 1 | AUX 2 |
HDMI 1 |
| HDMI 2 | HDMI 3 |
HDMI 4 |
| iPod | RADIO |
|
| ENTER |
|
MOVIE | MUSIC TAINMENT | OFF | |
|
| CINEMA DSP |
|
SURROUND | STEREO | ||
| ENTER |
| G |
|
|
| |
TOP MENU |
| MENU |
|
OPTION | SETUP | RETURN | I |
|
|
| |
TV VOL | CH | VOLUME |
|
TV | TV |
|
|
MUTE | INPUT | MUTE |
|
UNIVOLUME | SUR. DECODE | INTELLIBEAM | M |
|
|
| |
1 | 2 | 3 |
|
4 | 5 | 6 |
|
7 | 8 | 9 |
|
0 | +10 | ENT |
|
CODE SET |
|
|
|
TUNING | PRESET | CATEGORY |
|
INFO | MEMORY | SLEEP |
|
GENTER
G
/ 
IRETURN
ISETUP
MINTELLIBEAM
■Assembling the supplied cardboard microphone stand
12
Remove
Fit in
3 | Fit in | 4 | Place horizontally |
|
|
5
Run through
y
•If a subwoofer with adjustable volume and crossover frequency controls is connected to this unit, turn it on, set the volume to about half way and then set the crossover frequency to the maximum as shown below.
VOLUME | CROSSOVER |
| HIGH CUT |
MIN MAX | MIN MAX |
Subwoofer
Using AUTO SETUP (IntelliBeam)You can select one of the following AUTO SETUP types depending on your purpose.
“BEAM+SOUND OPTIMZ”
(Beam optimization and sound optimization)
Use to optimize the beam angle, delay, volume, and quality so that the parameters best match your listening environment. It is recommended that you should select this optimization feature in the following cases:
•If you make settings for the first time
•If the unit has been relocated
•If your listening room has been restructured
•If the objects in your listening room (furniture, etc.) have been rearranged
This menu takes about three minutes.
“BEAM OPTIMZ ONLY”
(Beam optimization only)
Use to optimize the beam angle so that the parameter best matches your listening environment.
This menu takes about one minute.
“SOUND OPTIMZ ONLY”
(Sound optimization only)
Use to optimize the beam delay, volume, and quality so that the parameters best match your listening environment. You must optimize the beam angle with “BEAM OPTIMZ ONLY” before starting “SOUND OPTIMZ ONLY”. It is recommended that you should select this optimization feature in the following cases:
•If you have opened or closed the curtains in your listening room before using this unit
•If you have manually set the beam angle.
This menu takes about three minutes.
Notes
•It is normal for loud test tones to be output during the AUTO SETUP procedure. Make sure that there are no children around in the listening room while the AUTO SETUP procedure is in progress.
•Make sure that your listening room is as quiet as possible. For accurate measurement, turn off air conditioner or other devices that make noises.
•To achieve the best results possible, vacate your listening room until the AUTO SETUP procedure is completed so that you may not obstruct the path of sound beams.
•If there are curtains in your listening room, we recommend following the procedure below.
1.Open the curtains to improve sound reflection.
2.Run “BEAM OPTIMZ ONLY”.
3.Close the curtains.
4.Run “SOUND OPTIMZ ONLY”.
y
•To return to the previous screen while using SET MENU, press
IRETURN.
1Press ISETUP.
The remote control keys to be used and available operations in each step are displayed at the bottom of the screen.
SET MENU.;MEMORY ;AUTO SETUP ;MANUAL SETUP
;SOUND SET MENU ;SOUND OUT MENU ;INPUT MENU ;DISPLAY MENU [p]/[p]:Up/Down [ENTER]:Enter
y
•You can also start the “BEAM+SOUND OPTIMZ” procedure simply by holding down MINTELLIBEAM for
more than two seconds. In this case, proceed to step 4.