York 00497VIP manual • Seiko, Hardware required, Connectors, •WEIGH-TRONIXPrinter, Model

• SEIKO

Microboard	Printer	Function
J2-4	pin 3	Tx (data to printer)
J2-2	pin 8	DSR (busy signal from printer)
J2-9	pin 5	Gnd
Cabinet		shield

Hardware required:

Cable – #18 AWG stranded 50ft. maximum length.

Connectors –

-Microboard: None. Strip 1/4" insulation from wire and insert into screw terminal block.

-Printers: Okidata - 25 pin plug DB-25P or equiva- lent; Shell DB-C2-J9 or equivalent. Weigh-Tronix - Same as Okidata. Cable assembly available from Weigh-Tronix. Seiko - 9-Pin D-type Subminiature (DB-9 pin male).

PRINTER SETUP

The selected printer must be configured as follows. Refer to manual provided by Printer manufacturer with respective Printer.

•OKIDATA 182, 182 turbo, 184 turbo Printer CONTROL BOARD Switch settings:

SW1	- on	Unslashed 0
2	- off	Unslashed 0
3	- off	Unslashed 0
4	- off	Form Length 11 in.
5	- on	Form Length 11 in.
6	- off	Auto Line Feed off
7	- on	8 bit data
8	- off	Enable front panel

If equipped with a SUPER SPEED serial Board:

SW1-1	- on	Odd or even parity
1-2	- on	No parity
1-3	- on	8 bit data
1-4	- on	Protocol ready/busy
1-5	- on	Test select
1-6	- on	Print mode
1-7	- off	SDD(-) pin 11
1-8	- on	SDD(-) pin 11
2-1	- on	1200 Baud*
2-2	- on	1200 Baud*
2-3	- off	1200 Baud*
2-4	- off	DSR active

		FORM 50.40-OM2
2-5	- on	Buffer threshold 32 bytes
2-6	- on	Busy signal 200ms
2-7	- on	DTR space after power on
2-8	- not used

If equipped with HIGH SPEED serial board:

SW1	- off	(-) Low when busy
2	- off	1200 Baud*
3	- off	1200 Baud*
4	- on	1200 Baud*
5	- not used
6	- off	no parity
7	- off	Pin 20 & pin 11 act as busy line

•WEIGH-TRONIX Printer

-IMP-24 Model 2600

SW1	- off	1200 Baud*
2	- on	1200 Baud*

Model 1220

-Configure Menu Baud= 1200 Data Bits = 8 Stop Bits = 1 Hshake = Busy-Line

Cols = 32

Invert = No

Font = 5 x 84

Mag = None

-Custom Menu Auto Seq = No Zero = 0 Pound sign = # _(Underscore) Busy invert = no Online/offline = yes Ext Ch Set = no Print ready = yes

Set Clock = not used

Reset Seq = not used

• SEIKO
DipSW1-1 = off		Input-Serial
1-2 = on		Printing speed high
1-3 = on		Auto loading - on
1-4 = off		Auto LF - off
1-5 = on		Setting Command - Enable
1-6	= off	Printing density - 100%
1-7	= on	Printing density - 100%
1-8	= on	Printing, density - 100%

YORK INTERNATIONAL 61