C-30HDG PUMP — PUMP COMPONENTS

Figure 7 illustrates the location of the major components for the C-30HDG Concrete Pump. The function of each component is described below:

1. Discharge Cone – Connect 3" elbow to this discharge port, then connect 3" x 2" reducer to elbow.

2.Discharge Cone Safety Latch – When towing of the pump is required, ALWAYS secure the discharge cone to latch located on the manifold.

3. Rear Running Lights – ALWAYS check and make sure both the right and left running lights are functioning correctly before towing the pump.

4.Hopper – Concrete from a Redi-Mix truck is poured into this hopper. The hopper can hold 6.0 cu. ft of concrete. NEVER put hands or any other parts of you body into the hopper.

5.Safety Grill – The safety grill should be locked at all times when the pump is being towed. Under normal working conditions, raise and place the safety grill on the support hooks which are located on splash guard.

6.Compartment Hood – NEVER operate the pump with the hood removed. Installed on the pump frame is a safety inter- lock device which prevents the engine from starting if the hood is removed or in the up position (open).

7.Hood Fastener – When the hood is in the down position, secure the rubber latch to this fastener.

8.Hood Lift Handle – Grip this handle, pull upward then back to raise the compartment hood.

9.Control Box – Contains the mechanical and electrical components required to run the pump. Below is a list of those components:

■Throttle Control Switch

■Pumping Control

■Check Engine Indicator

■Hood Open Indicator

■Engine Hour Meter

■Ignition Switch

■Remote Connector

10. Radiator/Cap – Fill with a water/anti-freeze type solution as recommended in the maintenance section of this manual. ALWAYS make sure that the radiator is filled to the proper operating level before starting the engine.

11. Fuel Tank/Cap – Fill with unleaded fuel. Fuel tank (cell) holds approximately 11 gallons (42 liters). DO NOT top off fuel. Wipe up any spilled fuel immediately

12. Tow End Jack Stand – Use this jack stand to level and support the pump.

13. Tow Hitch Coupler – Requires a 2-inch ball hitch or a 3- inch pintle. Capable of towing 5,000 lbs.

14. Safety Chain – ALWAYS attach safety chain to the towing vehicle. NEVER! tow the pump with the safety chain unattached.

15. Engine Safety Device –This device will return the engine speed to idle if the compartment hood is in the UP position. The compartment hood must be in the DOWN position for the pump to operate at high rpm's.

16. Grease Port Console – This console allows for the remote lubrication of components on the pump.

17. Access Door – There are four access doors on the pump. Remove these door to gain access to drive and piston assemblies when maintenance is required.

18. Drive Chain – Keep this chain properly lubricated and aligned at all times. Lubricate this chain as specified in the maintenance section of this maintenance.

19. Rubber Latch – Secure this rubber latch to the hood fastener whenever the pump is in use or being towed.

20. Tires Ply– The tire ply (layers) number is rated in letters; This trailer uses 4-ply tires.

21. Chock Blocks – Place these blocks (not included as part of your concrete pump package) under each trailer wheel to prevent rolling.

22. Pump End Jack Stand – Use this jack stand to level and support the pump.

23. Discharge Cone Release Lever – secures the discharge cone to the "Y" manifold; also relieves manifold pressure.

24. Documentation Box – Contains engine and pump operation, parts and maintenance information.

25. Lubrication Box – This box is empty when shipped from the factory. Please fill with 7 gallons ( 26.5 liters) of SAE motor oil for first time use. Also check the dual clean-out point on bottom of lubrication box for a secure tight fit.

26. Overflow Bottle – Fill with coolant. Maintain coolant at proper level. See fluid level markings on side of bottle.

27. Cam Bearing – Felt ring must be peridically lubricated applying 4 or 5 drops of 30 wt. motor oil until the felt ring is moist.

MAYCO C-30HDG PUMP — OPERATION AND PARTS MANUAL — REV. #6 (04/02/12) — PAGE 23

Page 22 Page 24
Page 23
Image 23
Zenith C-30HDG manual 30HDG Pump Pump Components
Page 22 Page 24

C-30HDG specifications

The Zenith C-30HDG is a standout in the world of gaming monitors, tailored specifically for gamers who seek both high performance and stunning visuals. This monitor excels in delivering a riveting experience, combining advanced technology with robust features that cater to the needs of competitive gamers and casual enthusiasts alike.

One of the main features of the Zenith C-30HDG is its impressive 30-inch display size, providing an immersive gaming experience with ample screen real estate. With a resolution of 2560 x 1080 pixels, this ultrawide monitor offers a 21:9 aspect ratio, which expands the field of view in games, allowing players to spot enemies and navigate expansive environments more effectively. The curved design further enhances immersion, wrapping the visuals around the viewer's peripheral vision.

Another key characteristic of the Zenith C-30HDG is its rapid 200Hz refresh rate, enabling smooth motion and reduced motion blur during high-paced gaming sessions. This feature is particularly beneficial for fast-action games, where every millisecond counts. Complementing the refresh rate is a low response time of 1ms, ensuring that ghosting effects are minimized, resulting in crisp visuals even during intense gameplay.

The monitor supports AMD FreeSync and NVIDIA G-Sync technologies, which work to eliminate screen tearing and stuttering, providing a seamless and tear-free gaming experience. Whether users are playing an action-packed shooter or an expansive role-playing game, the display's adaptive synchronization ensures that they stay fully engaged without distractions.

In terms of connectivity, the Zenith C-30HDG is well-equipped with multiple HDMI and DisplayPort inputs, making it easy to connect to a variety of devices, including gaming consoles, PCs, and laptops. This versatility caters to gamers who utilize multiple platforms for their gaming experiences.

The Zenith C-30HDG also integrates advanced color accuracy features, supporting a wide color gamut with rich and vibrant colors that bring games to life. With built-in settings for different gaming genres, users can optimize their visual experience based on the type of game they are playing.

In conclusion, the Zenith C-30HDG is a remarkable gaming monitor that offers an outstanding combination of size, resolution, and advanced technologies. Its features cater not only to competitive gamers seeking the best performance but also to casual gamers who appreciate breathtaking visuals. With the Zenith C-30HDG, gamers can elevate their experience and fully immerse themselves in their favorite worlds.
Top Page Image Contents