Quick Guide (2) Playing the Preset Pads

The ST-224 allows assigning sampled sounds to pads and playing these manually (pad play). You can try out

the preset sounds that are assigned to the pads at the factory.

 

[Preparations ]

 

 

 

 

 

• Connect the ST-224 to the playback equipment (

p. 8).

 

 

 

 

• The Quick Guide assumes that the ST-224 is in the

 

Headphones

 

 

 

factory default condition. To return the ST-224 to the

 

 

 

OUTPUT R

 

Playback equipment

 

factory default condition, hold down the [SAVE] key

 

 

t

 

 

 

 

while turning power to the unit on in step .

 

 

 

 

 

PHONES

OUTPUT L/MONO

 

 

 

 

ZOOM CORPORATION MODEL

 

300mA

 

 

MADE IN JAPAN

 

 

 

LINE/MIC

R L/MONO

PHONES R L/ MONO

DATA CARD

MIDI IN DC9V POWER

 

 

INPUT

OUTPUT

 

 

Guide Quick

 

L/MONO R

PHONES

 

L/MONO

R MIC/LINE

 

 

 

 

OUTPUT

 

 

INPUT

 

 

 

 

 

 

 

 

OUTPUT

 

INPUT

 

 

 

 

 

MIN

MAX

 

MIN

MAX

 

 

 

 

 

 

 

 

 

PEAK

 

 

BPM/VALUE

 

 

 

SAMPLING

 

 

 

 

 

 

 

GRADE

MONO

RE-SAMPLE

 

 

 

 

 

 

 

STEREO

 

 

 

 

 

 

 

 

 

 

 

 

MEASURE

BEAT

SAMPLE/SONG

 

RECORD

PLAY/STOP

OPY

 

DELETE

–

+

 

 

 

 

 

 

 

 

 

 

 

 

 

EXIT

 

BACKUP

 

 

PAD ASSIGN CAPACITY ERASE OPTIMIZE

LOAD

SAVE INTERNAL/DATA CARD

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FUNCTION

 

 

 

 

 

 

 

 

PAD

 

 

 

5

 

 

 

 

SONG

 

START POINT

END POINT

7

 

 

 

 

 

 

 

 

 

REVERSE

 

 

 

 

TIME SIG

 

PRE COUNT

 

 

 

 

 

 

 

CLICK VOLUME

 

 

 

 

 

 

 

 

 

 

 

 

4

OFFSET

6

PANNING

 

 

 

 

 

 

 

8

 

 

BANK

2

 

 

SHIFT

 

 

TRIGGER/GATE

 

 

 

SWING

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MIDI

 

3

 

 

 

 

 

 

 

 

BANK

LOOP/MARK

d

Turn power on in the order ST-224 playback equipment. Adjust the

[OUTPUT] knob on the ST-224 and the volume control on the playback equipment to obtain the desired volume.

Hit any of the pads 1 - 8 to try out the sound.

When you hit a pad, its LED lights up and the preset sampling content is played. Pads 1 - 8 are preprogrammed with different samples.

To switch pads 1 - 8 to a different bank, press the [BANK 2] key.

The ST-224 incorporates three banks (groups of settings for pads 1 - 8). In the factory default condition, banks 1 and 2 are preprogrammed with different samples.

To repeat the sound of a pad, hit the pad while holding the [LOOP/MARK] pad down.

While the [LOOP/MARK] pad is held, the sound of a pad is looped.

11