Husqvarna CTH126 instruction manual To Install Bagger Component to Tractor, Front of Tractor

Page 25

2

TO INSTALL BAGGER FULL LEVER/PADDLE

TO INSTALL BAGGER COVER PANEL

• Before installation, tractor engine must be shut off and

•

parking brake engaged.

 

•Standing behind the tractor with the bagger removed from the

backplate (1), identify the bag full switch (2) area. (See Fig 1)

•

2

 

 

 

 

1

 

 

 

 

Fig. 1

 

 

 

 

FRONT OF TRACTOR

 

 

 

4

 

4

 

5

 

 

 

 

3

 

 

 

 

3

 

 

 

•

 

2

7

 

 

 

 

6

8

Fig. 2

 

Fig. 3

 

 

 

•Take bagger full lever (3) and insert tab(4) into upper slot and rotate until lever (3) snaps into position (See Figs. 2 and 3)

•For the heaviest/wet grasses, do not attach paddle (5).

•For lighter grasses use the paddle (5) on setting “1”, “2”, or “3” (“3” being for the lightest or dry grass).

•Choose your setting and rotate the bagger paddle (5) so that the desired number (setting) faces you.

•Place paddle (5) on lever (3) so that tab (6) at the bottom of

the bagger full lever (3) goes through appropriate rectangular

•

slot and make sure holes in bagger full lever (3) and paddle

 

(5) line up.

•

• Feed screw (7) through bagger full paddle (5) and lever (3)

 

holes and fasten using nut (8) (See Fig. 3)

 

• Setting may be changed by loosening fasteners (7 and 8),

 

removing/rotating paddle (5), and tightening again.

 

TO INSTALL BAGGER COMPONENT TO TRACTOR

1

3

2

1

 

Install bagger cover panel (1) by angling plastic posts at front of cover panel (1) into corresponding slots at the front of the bagger top.

Swing back end of cover panel (1) down until it rests on bagger cover.

1

Slide whole bagger cover panel (1) rearwards so that teeth under the opening in the cover panel slide into the teeth in the handle portion of the bagger cover.

1

1

Apply push nuts (2) to plastic posts to secure cover panel (1) in the front.

Secure rear side of cover panel (1) to bagger top, and fasten by threading two screws (3) up through rear bagger top handle into the cover panel (1).

1

2

3

•Before installation, tractor engine must be shut off and parking brake engaged.

•Install latch springs (1) in mounting holes on back plate.

•Insert hex bolt (2) through each latch spring hole and corresponding hole in back plate.

•Fasten lock nut (3) to bolt on the other side of back plate.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents CTH126 Page Training Safety RulesII. Preparation III. OperationIV. Maintenance and Storage Schulung SicherheitsvorschriftenII. Vorbereitung III. BetriebIV. Wartung UND Lagerung Précautions D’UTILISATION Règles de SécuritéII. Préparation III. UtilisationIV. Entretien ET Entreposage Instrucción Reglas De SeguridadII. Preparación III. OperaciónIV. Mantenimiento Y Almacenamiento Addestramento ALL’USO Norme AntinfortunisticheII. Preparazione III. FunzionamentoIV. Manutenzione E Periodi DI INATTIVITA’ II. Voorbereiding VeiligheidsregelsIII. Bediening Maai alleen bij daglicht of goed kunstlicht12,5/9,3 IV. Onderhoud EN Opslag190 Reverse Directive for Safety Explosive Gase SER Ausspülen Züglich MIT WASSofort Ärztliche Hilfe AufsuchenSteering Wheel Volant DE DirectionLenkrad Volante DE DirecciónAdjust Seat Install SeatSitz Montieren Einstellen DES SitzesInstallatie VAN DE Stoel Installazione DEL SedileInstalación DEL Asiento Ajustar EL AsientoInstallazione Della Batteria Install Battery Einbau DER BatterieAccu Installeren Mise EN Place DE LA Batterie02604 Handle insert To Assemble BaggerTurn assembly right-side up Front of Tractor To Install Bagger Component to TractorMontage DER Grasfangbox DER Schaufel Installation DES Beutelvollhebels UNDDen Grasfänger umdrehen Installation DER Aufhängung DER Grasfangbox DES Traktors Installation DES SackdeckelsPlacez le bac 3 à l’envers, alignez les orifices du châssis Pour Assembler LE CollecteurPartie inférieure du châssis avant du bac 14 et serrez les En caoutchoucPour Assembler Composants DU Collecteur Pour Installer LE Levier DE Vidage DU BAC Avec LA PalettePara Montar EL Contenedor Paleta Para Instalar EL Brazo Completo CONGire el lado derecho hacia arriba DE LA Ensacadora Para Instalar EL Panel DE RecubrimientoPara Montar LOS Componentes DEL Contenedor AL TractorPER Montare IL Cesto DI Raccolta Allineare i fori nel deflettore erba 29 con le protuberanze Estremità del sacco sul tubo del telaio per il sacco in altoPER Montare I Componenti DEL Cesto DI Raccolta PER Montare UNA LEVA/PALA Riempimento SaccoPER Montare IL Pannello DI Copertura DEL Sacco DE Grascontainer Monteren VOL-HENDEL/SCHOEP HET Installeren VAN DE OpvangbakZet de assemblage weer met de goede kant naar boven DE Dekplaat VAN DE Opvangbak Bevestigen Schnelles Heben und Senken des Mähaggregats Ubicación de los mandos Emplacement des commandesComandi De plaats van de bedieningsorganenGas und kaltstarthebel Commande des gaz et starterMandos del acelerador y del estrangulador Comando gas/chokeKupplungs-/Bremspedal Clutch/Brake PedalPédale de frein/D’embrayage Pedal del embrague/FrenoConnection/disconnection of the cutting unit Commande dembrayage et de débrayage du carter de coupeEin und Ausschalten des Mähaggregats Acoplamiento y desacoplamiento del equipo de corteSchnellesHebenundSenkendesMähaggregats Quick lifting/lowering of the cutting unitRelevage et abaissement du carter de coupe Elevación/descenso rápidos delequipodecorteZündschloß Ignition LockClé de contact et de démarrage Cerradura de encendidoFeststellbremse Parking brakeFrein de stationnement Freno de estacionamientoService Reminder/Studenzähler Service Reminder/HourmeterFree-wheel Control Lever Ein und Ausschalten des FreilaufesReposición de combustible Filling upTanken Plein de carburantÖlstand Oil levelNiveau d’huile Nivel de aceiteStarting of motor Driving . Betrieb . Conduite Conducción . Guida . RijdenHinweis Entlüften DES Getriebes Purge TransmissionPurge DE LA Transmission Purgar LA TransmisiónTransmissie Ontluchten Spurgo Della TrasmissioneHinweis RemarqueVorwärts- und Rückwärtsbewegung To Move Forward and BackwardPour avancer et pour reculer Moverse hacia adelante y hacia atrásRückwärtsgangsystem ROS Reverse Operation System ROSSécurité Marche Arrière ROS Sistema de Funcionamiento Atrás ROSSysteem voor achteruit ROS Sistema per operazioni in retromarcia ROSCutting tips Ratschläge zum RasenmähenConsejos para el corte Conseils pour la tonteConsigli per il taglio dell’erba MaaitipsAdvertencia WarnungPericolo WaarschuwingAbschalten des Motors Switching off the engineExtinction du moteur Apagar el motorAdvertencia Motorhaube Engine hoodCapot moteur Cubierta del motorWartung MaintenanceEntretien MantenimientoWartung des Motors To service enginePour assurer lentretien du moteur Mantenimiento del motorWartungsnachweis Service RecordInforme DE Servicio Schema DentretienDati DI Servizio Service AantekeningenFahrer-Anwesenheitssystem und Rückwärts- gangsystem ROS Operator Presence System and Reverse Opera- tion System ROSControl Sistema Presencia Operador Messerbalken BladesLames Lame CuchillasMessen Überprüfen der Bremse To Check BrakePour vérifier le frein Controlar el FrenoTo Remove Mower PL QEntfernen Des Mähers Pour Démonter La FaucheusePer Rimuovere La Falciatrice Assembly of the cutting unitEinbau des mähdecks Mise en place du carter de coupeAustauschen des Antriebsriemens des Mähers To Replace Mower Drive BeltSustituir la correa de transmisión cortacésped Pour remplacer la courroie de transmissionSostituzione della cinghia di trasmissione del rasaerba Installare la chinghia sulla puleggia di frizione MDe aandrijfriem van de maaiunit vervangen Visual SIDE-TO-SIDE Adjustment FRONT-TO-BACK AdjustmentPrecision SIDE-TO-SIDE Adjustment To Level MowerVisuelle Justierung AN Beiden Seiten Ausnivellieren des MähersGenaue justierung an beiden seiten Gleich sindRéglage Visuel Bilatéral Pour mettre la tondeuse à niveauRéglage Bilatéral DE Précision Réglage D’AVANT EN ArrièreAjuste Visual DE Lado a Lado Nivelar el cortacéspedAjuste DE Precisión DE Lado a Lado Ajuste DE LA Parte Delantera a LA TraseraRegolazione Visiva LATO-LATO Livellamento del rasaerbaRegolazione DI Precisione LATO-LATO Regolazione DAVANTI-DIETROBeide Kanten OP HET OOG Uitlijnen De maaiunit nivellerenPRECISIE-AFSTELLING BAN Beide Kanten BAN DE Maaiunit Afstelling BOOR-EN AchterzijdeRemplacement de la courroie dentraînement Replacement of drive beltAuswechsein des Treibriemens Cambio de correa propulsoraTRANSACHSEN-KÜHLUNG Transaxle CoolingRefroidissement DE LA Transmission Enfriamiento DEL TransejeService REMINDER/STUNDENZÄHLER Service REMINDER/HOUR MeterRappel D’ENTRETIEN/COMPTEUR Horaire Recordatorio MANTENIMIENTO/CUENTA- HorasTroubleshooting . Störungssuche Recherche des pannes . Búsqueda de averías Ricerca guasti . Het localiseren van fouten Storage . Aufbewahrung . Remisage . Conservación ServiceEntretien et réparations ServicioServizio Rismessaggio . Stallen532 42 26-98 12.03.08 AP

CTH126 specifications

The Husqvarna CTH126 is a highly regarded ride-on lawn mower designed for homeowners who require efficiency, comfort, and reliability in their mowing tasks. This powerful machine combines innovative features with a user-friendly design, making it an excellent choice for maintaining medium to large-sized lawns.

One of the standout characteristics of the CTH126 is its robust engine. Powered by a reliable and efficient 540cc Briggs & Stratton gasoline engine, it delivers ample torque and power, ensuring that the mower can handle tough grass and varied terrains. The engine's design enhances fuel efficiency and reduces emissions, making it an environmentally friendly option for lawn care.

The cutting deck of the Husqvarna CTH126 is another notable feature. With a 42-inch cutting width, it allows for faster mowing sessions, covering larger areas in less time. The deck is made from durable materials to withstand the rigors of frequent use, and it includes a cutting height adjustment feature, allowing users to easily change the height of the cut from 1.5 to 4 inches, ensuring optimal results for various lawn types and conditions.

One of the technologies that sets the CTH126 apart is its ergonomic seating and controls. The riding mower is designed with comfort in mind, featuring an adjustable seat that accommodates operators of different sizes. The intuitive dashboard layout includes easy-to-reach controls for throttle, choke, and blade engagement, allowing users to focus on mowing without distraction.

Moreover, the Husqvarna CTH126 is equipped with a tight turning radius, enhancing its maneuverability. This feature allows the mower to navigate obstacles such as flower beds and trees effortlessly, making it easier to achieve a clean and well-manicured lawn. The mower's front suspension system further contributes to a smooth ride, reducing operator fatigue during longer mowing sessions.

In terms of maintenance, the Husqvarna CTH126 is designed for ease of access, making routine checks and service hassle-free. With features like a removable deck for cleaning and a built-in battery charger, owners can keep their mower in top shape with minimal effort.

Overall, the Husqvarna CTH126 combines powerful performance, user-friendly design, and innovative technologies to provide an exceptional lawn mowing experience, making it a solid investment for homeowners dedicated to maintaining pristine outdoor spaces.
Top Page Image Contents