Husqvarna 460 Rancher Air filter, Tensioning the recoil spring, Changing a broken recoil spring

Page 36

MAINTENANCE

recoil spring by letting the pulley rotate slowly backwards.

1 2

•Undo the screw in the centre of the pulley and remove the pulley. Insert and fasten a new starter cord to the pulley. Wind approx. 3 turns of the starter cord onto the pulley. Connect the pulley to the recoil spring so that the end of the spring engages in the pulley. Fit the screw in the center of the pulley. Insert the starter cord through the hole in the starter housing and the starter handle. Make a secure knot in the end of the starter cord.

Tensioning the recoil spring

•Hook the starter cord in the notch in the pulley and turn the starter pulley about 2 turns clockwise.

Note! Check that the pulley can be turned an additional 1/2 turn when the starter cord is pulled all the way out.

1

2

Changing a broken recoil spring

•Lift off the pulley. See instructions under heading Changing a broken or worn starter cord.

•Remove the recoil spring from inside the pulley by tapping the pulley lightly with its inside face downwards against a work bench or the like. If the spring pops out during fitting, wind it up again, working from the outside in towards centre.

•Lubricate the recoil spring with light oil. Fit the pulley and tension the recoil spring.

Fitting the starter

•To fit the starter, first pull out the starter cord and place the starter in position against the crankcase. Then slowly release the starter cord so that the pulley engages with the pawls.

•Fit and tighten the screws that hold the starter.

Air filter

The air filter must be regularly cleaned to remove dust and dirt in order to avoid:

•Carburettor malfunctions

•Starting problems

•Loss of engine power

•Unnecessary wear to engine parts

•Excessive fuel consumption.

•Remove the air filter after taking off the air filter cover. When refitting make sure that the air filter seals tightly against the filter holder. Clean the filter by brushing or shaking it.

The filter can be cleaned more thoroughly by washing it in water and detergent.

36 – English

115 13 82-96 Rev.1 2009-03-26

Page 35 Page 37
Image 36
Page 35 Page 37
Contents 455e Rancher Rancher 460 Rancher KEY to Symbols Symbols on the machineSymbols in the operator’s manual You will find the following labels on your chain saw EPAContents Introduction Dear customerWhat is WHAT? What is what on the chain saw?General Safety Precautions Before using a new chain sawAlways use common sense Machine′s safety equipment Personal protective equipmentChain brake and front hand guard 115 13 82-96 Rev.1 English Throttle lockout Chain catcherRight hand guard Vibration damping systemStop switch Cutting equipmentMuffler General rulesCutting equipment designed to reduce kickback BarChain Sharpening your chain and adjusting depth gauge setting General information on sharpening cutting teethTensioning the chain Lubricating cutting equipment 455e RancherFilling with chain oil Checking chain lubrication Chain drive sprocketNeedle bearing lubrication Checking wear on cutting equipmentBar Assembly Fitting the bar and chainRancher, 460 Rancher 455e RancherAssembly Fuel Handling FuelFuel safety FuelingTransport and storage Long-term storageStarting and Stopping Starting and stoppingCold engine Warm engineStopping Basic safety rules Working TechniquesBefore use General working instructionsGeneral rules Basic cutting technique TermsLimbing Tree felling technique Safe distanceFelling direction Clearing the trunk and preparing your retreatDirectional cuts Felling cutGeneral advice Freeing a tree that has fallen badlyFreeing a trapped tree Cutting trees and branches that are in tensionHow to avoid kickback What is kickback?Cutting the trunk into logs Maintenance Carburetor adjustmentGeneral Correctly adjusted carburetor When the bar hits the stump the brake should be appliedChecking brake band wear Checking the front hand guardChecking the brake trigger ImmediatelyMuffler StarterChanging a broken or worn starter cord Air filter Tensioning the recoil springChanging a broken recoil spring Fitting the starterAdjustment of the oil pump Spark plugLubricating the bar tip sprocket Needle bearing lubricationAir Injection centrifugal cleaning Temperature 0C 32F or colderTemperature -5C 23F or colder Cooling systemMaintenance schedule Daily maintenance Weekly maintenance Monthly maintenanceTechnical Data Technical dataBar and chain combinations Saw chain filing and file gaugesFederal Emission Control Warranty Statement Your Warranty Rights and ObligationsAmerican Standard Safety Precautions Safety precautions for chain saw usersKickback safety precautions Other safety precautionsAclaracion DE LOS Simbolos Símbolos en la máquinaSímbolos en el manual de instrucciones Etiquetas que se encuentran en la motosierra Indice ÍndiceIntroduccion Apreciado cliente¿QUE ES QUE? ¿Qué es qué en la motosierra?Instrucciones Generales DE Seguridad Medidas a tomar antes de utilizar una motosierra nuevaImportante Emplee siempre el sentido común Equipo de protección personalEquipo de seguridad de la máquina Freno de cadena con protección contra reculadasInstrucciones Generales DE Seguridad Fiador del acelerador Captor de cadenaEquipo de corte Protección de la mano derechaSistema amortiguador de vibraciones Botón de paradaReglas básicas Equipo de corte reductor de reculadasEspada CadenaGeneralidades sobre el afilado de los dientes cortantes Tensado de la cadena Afilado de dientes cortantesGeneralidades sobre el ajuste de la profundidad de corte Rancher Lubricación del equipo de corte Repostaje de aceite para cadena de motosierraControl de la lubricación de la cadena Piñón de arrastre de la cadena Lubricación del cojinete de agujasControl del desgaste del equipo de corte ¡ATENCION! La mayoría de losMontaje Montaje de la espada y la cadena¡ATENCION! Para manipular la cadena Deben utilizarse guantes protectoresMontaje del apoyo de corteza Manipulacion DEL Combustible CarburanteRepostaje Seguridad en el uso del combustibleTransporte y almacenamiento Almacenamiento prolongadoArranque Y Parada Arranque y paradaMotor frío Motor calienteParada Tecnica DE Trabajo Antes de utilizar la máquinaInstrucciones generales de trabajo Reglas básicas de seguridadReglas básicas Técnica básica de corte DesignacionesDesramado Tronzado ¡ATENCION! No intente nunca serrarTécnica de tala Distancia de seguridadDirección de derribo Corte de ramas bajas y camino de retiradaCorte de indicación Corte de derriboTratamiento de una tala fallida Derribo de un árbol atascadoCorte de árboles y ramas tensos Medidas preventivas de las reculadas ¿Qué es la reculada?¡No corte nunca del todo un objeto en tensión ¡ATENCION! Las reculadas pueden serMantenimiento GeneralidadesAjuste del carburador Surtidor de pleno régimen H Carburador correctamente reguladoControl del desgaste de la cinta de freno Control de la protección contra reculadasControl de la función de inercia Detenerse inmediatamenteSilenciador Mecanismo de arranque Cambio de un cordón de arranque roto o desgastadoTensado del muelle de retorno Cambio de un muelle de retorno rotoFiltro de aire BujíaEngrase del cabezal de rueda de la espada Montaje del mecanismo de arranqueLubricación del cojinete de agujas Ajuste de la bomba de aceiteSistema refrigerante Depuración centrífuga Air InjectionUtilización en invierno Temperaturas de 0C o más fríasTemperaturas de -5C 23F o inferiores Programa de mantenimiento Datos Tecnicos Datos técnicosCombinaciones de espada y cadena Afilado y calibres de afilado de la cadena de sierraPulgadas Pulgadas/mm De arrastre unidadGarantia DEL Sistema DE Control DE Emisiones SUS Derechos Y Obligaciones DE GarantiaPrecauciones DE Seguridad DE LA Norma Americana Precauciones de seguridad para usuarios de motosierrasPrecauciones de seguridad en reculadas Otras precauciones de seguridad115 13 82-96 Rev.1 115 13 82-96 Rev.1 115 13 82-96 Rev.1 ´z+SF=¶6*¨ 115 13 82-96 Rev.1 1151382-96

115 13 82-96, 460 Rancher specifications

The Husqvarna 115 13 82-96,460 Rancher is a powerful and versatile chainsaw designed to meet the needs of both homeowners and professionals. This model is particularly well-suited for those who require a reliable tool for light to medium-duty applications, such as tree trimming, pruning, and firewood cutting.

One of the standout features of the 460 Rancher is its impressive 60.3cc X-Torq engine. This engine delivers excellent power while ensuring optimal fuel efficiency and reduced emissions. The X-Torq technology minimizes fuel consumption by up to 20% compared to standard engine designs, making this chainsaw environmentally friendly and cost-effective to operate.

The 460 Rancher is equipped with a durable 18-inch guide bar, allowing for a deeper cutting capacity. Coupled with a high-performance chain, it provides smooth cutting performance through various types of wood. The chainsaw’s automatic oiling system ensures that the bar and chain receive adequate lubrication while in use, extending the lifespan of components and improving performance.

User comfort and ease of use are further enhanced by the lightweight design and ergonomic handle. The front handle features an anti-vibration system that reduces fatigue during extended use, allowing operators to work for longer periods without discomfort. Moreover, the chainsaw includes a quick-release air filter that simplifies maintenance, making it easy to keep the tool in top working condition.

Another notable technology in the 460 Rancher is the Smart Start system, which allows the chainsaw to start with minimal effort. This feature is particularly beneficial for users who may not be as experienced with starting a chainsaw, making the tool accessible to a wider audience.

Safety features are also a priority with the Husqvarna 460 Rancher. It comes with a chain brake that automatically activates in the event of kickback, providing an additional layer of protection for the user. The chainsaw is also designed with a throttle lockout, preventing accidental throttle engagement.

Overall, the Husqvarna 115 13 82-96,460 Rancher is an exceptional chainsaw that combines power, efficiency, and user-friendly features. Whether for cutting firewood, tackling yard work, or handling forest jobs, this model stands out as a reliable and effective tool in the Husqvarna lineup.
Top Page Image Contents